kossel mini 3d models
89818 3d models found related to kossel mini.youmagine
This is the kossel mini effector with nut pockets I created because after a certain amount of experiments plastic failed to hold bolts very well.
thingiverse
Jig for 180mm carbon rod assembly (Kossel Mini) I didn't get a jig so I had to improvise my own.
grabcad
My first draft for a kossel mini effectorGoal: lots of ventilation, rod ends on bottom, E3D V6 and inductive sensor for bed leveling
thingiverse
... with the rods. ...The center hole is now big enough to fit a wider range of hotends (also the original Anycubic Kossel mini hotend). Print Settings Printer: Anycubic Kossel mini Rafts: Doesn't Matter Supports: Yes Resolution: 200 microns Infill: 30%
thingiverse
It is a slightly costomized fan duct for the kossel mini. It differs in angle and shape from the original. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
My design for a Kossel mini Frame brace. Really firms up the frame well. 3-4-2016 Improved design! extra sturdy. ...(frameBraceV4.st) I have created a version for the 1515 frame http://www.thingiverse.com/thing:1418574
thingiverse
Given the small amount of room underneath a standard Kossel mini I devised this solution that raises the unit up and provides additional space for electronics. ...Will update once I get it populated and installed.
thingiverse
Minimalistic plexi glass mount for Kossel mini enclosure. Minimal 12 copies of holder needed. ... Also you need: 12x M4 20mm Screw 12x M4 10mm Wing nut 12x M3 Screw 12x M4 hex nut 3x 2mm plexi glass (cca 375x500)
thingiverse
I found I could not merely widen the effector with the scad source (standard kossel mini) so I broke out some trig and made this parametric effector that would properly widen without leaving strange gaps. ... I haven't formatted it for customizer but...
thingiverse
... to optos, I am getting near perfect homing conditions. Print Settings Printer Brand: RepRap Printer: Kossel Mini Rafts: Doesn't Matter Supports: Doesn't Matter Notes: It's a functional non-load bearing part. ...Just get it printed and it'll work.
thingiverse
... the other piece of the spool holder; Fix the spool holder in the piece assempled in part 1. ...Enjoy! :) Print Settings Printer Brand: RepRap Printer: Kossel Mini Rafts: No Supports: No Resolution: 0.2mm Infill: 40% Notes: Use ABS for best durability.
thingiverse
I was trying to reuse my boatload of D4 microswitches on my Kossel Mini build. Tested in conjunction with electronhacks' Prime Line Roller Carriage instead of slides. http://www.thingiverse.com/thing:215438 Feedback welcome. ...Remixed from endstop.stl...
thingiverse
... Used superglue to secure SD card adaptor. ...Fold the SD card adaptor cable beneath circuitboard, *******NOTE: The case is lower than the Kossel Mini itself so the machine needs to be placed on a table/shelf edge typically******* Feel free to remix.
thingiverse
Bottom cover for Kossel Mini to help give it a clean look and conceal wires and electronics. SImple attachment via 3 printed clip that snap into the profile and the plate slips into the clips. ...Print Settings Printer: Tronxy...
thingiverse
This is a reinforcement for the 2020 aluminium extrusion of the kossel mini printer. You need to print 3 x Reinforcement 1 and 3 x Reinforcement 2. The screws are M4. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
WIP!!! ...A separate lager base for the Kossel Mini to store the power supply, controller, lcd, and etc? ...I am working on a design right now that uses a additional 6 400mm and 3 185mm extrusions, 3 1??mmx4??mm plexiglass and some printed parts.