krieger clones 3d models
12468 3d models found related to krieger clones.thingiverse
Xiaomi yi and vtx antenna mount for GE220 (Shendrones Krieger clone). Put your spacers in the holes and screw it together, finished ;) Uploaded "Yi mount IMPROVED" file, much easyer to print! Get your GE220 here for 33$! If you have any questions,...
thingiverse
... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: font_scale = 2.1 font_spacing = 0.81 word = Krieger pen_length = 130
thingiverse
My stinkin Krieger was always tipping over, breaking props so I designed the foot-thing to keep it more upright. It may not work worth a damn since I haven't tested it yet. It's intended to be printed with a flexible filament (tpu/ninjaflex/etc). ...I'm...
thingiverse
An aeropod for a krieger drone. V6 50 degree is about a 50 degree angle. It has 4mm wall thickness. This is the preferred pod for racing. V8 35 Degree is a modification of the previous with a shallower angle allowing for more relaxed flying. It has...
thingiverse
And here comes my Krieger Cookie Cutter ;-) visit: racequadgear.de
thingiverse
Krieger Shark Fin You also can find a cam mount for the Shendrones krieger here: https://www.thingiverse.com/thing:3213922
thingiverse
V2 version of my previous bumper for the shendrones krieger. ...reinforced for better use with TPU
thingiverse
Motor Guards for Shendrones Krieger 4mm Arm use support inside the ring
thingiverse
Aeropod for Shendrones Krieger. ...Print in TPU, versions for 2.8 and 2.1/2.5 lenses.
thingiverse
3 types of led monts for the shendrones krieger racing copter shark fin: https://www.thingiverse.com/thing:3216052 FPV Cam mount: https://www.thingiverse.com/thing:3213922
thingiverse
Zwischenstück für die Krieger Carbon FPV Cam Carbon Platte in Verbindung mit PZ0420M. ...Einfach 4 Stücke 1.75mm Filament durch die Löcher stecken und verschmelzen, oder wer M2 Polyamidschrauben hat, diese verwenden.
thingiverse
I found the plate to mount the camera on the Krieger and Kriegerpus frames to be inadequate. ...So I made a means of containing the camera and using the same mounting holes the plate uses instead of holding the camera to the plate with rubber bands.
thingiverse
This are front bumpers for your Krieger. Will work with flexible filament only, because you have to put them over the side plates. Print Settings Printer: TinyBoy ...
thingiverse
Thi is a cover to hide the electronic for the Krieger from Shendrones. it simply "clips" to the green standoff. You can remove it for easy access of the electronics. Print Settings Rafts: No ...
thingiverse
This is a skid designed to fit the ends of the arms on the ShenDrones Krieger. It comes up over the end of the arm and motor to help reduce damage on impact as well as keep dirt out. Print in TPU or similar for best results. ... Print Settings Printer...
thingiverse
Simple mounting for an iLap transponder that uses the cross-standoffs on the top of a Krieger. Usually when racing you won't be carrying an HD camera, and the top of the pod is a great location for reliable transponder readings. This design slots...
thingiverse
Wanted to use a TBS unify pro in my krieger, but there was no good way to mount it. Also recently purchased Crossfire, and likewise, there was no good way to configure the antennas. This mount should hold the weird Unify Pro pigtail in place, as well...
thingiverse
Awesome full body armor for the Shendrones Krieger FPV racing Frame
thingiverse
This is a simple snap-on arm protection for the Shendrones Krieger.