krypton atom model

My go-to try bar spinner is this one I've made. The stainless steel outer balls have a groove built right into them so they spin freely. I uploaded three different STL files for varying levels of precision. To install the stainless steel outer balls...

Customized version of http://www.thingiverse.com/thing:114247 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=114247 Instructions Using the following options:...

IMPORTANT: When fitting them, make sure they are fitted correctlyRemember to print two pairs of each typePlace the horizontal pieces on the print bedPrinting requires no supports100% filling.The material is best PETG but you can also use PLAIf you...

Here are the spinning rules in use. A customised version of thingiverse.com/thing:114247 Created with Customiser! ...Thingiverse apps/customiser/run?thing_id=114247 ...

Customized version of https://www.thingiverse.com/thing:114247 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=114247 Instructions Using the following settings: pin_hole_radius = 3...

A personalized rendition of http://www.thingiverse.com/thing:116807 was crafted using the Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=116807). The specifications employed include pin_hole_radius = 0, pin_cap_gap = 0,...

All rights reserved by Berend Jozef Moes. Visit www.berendjozef.wix.com/eternalflower for more information. ...The formula used to create this unique geometry is strictly copyrighted, so consult with Berend Jozef Moes before using any shapes or...

A customized version of http://www.thingiverse.com/thing:114247 has been created using the Customizer! ...(http://www.thingiverse.com/apps/customizer/run?thing_id=114247) with specific options including pin_cap_gap of .45, pin_cap_width of 4,...

Using the following options, I will customize the settings: pin_cap_width: Set to 6 for a more secure grip. Font: Change to write/orbitron_stroke.dxf for a bold aesthetic. ring_height: Increased by 1 inch to make it easier to read. ring_spacing:...

Customized version of http://www.thingiverse.com/thing:114247 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=114247 Instructions Using the following options: Build_Plate_Manual_Width = 100 Build_Plate_Type =...

I made this bracket because my light was grounding

I'm planning to test the durability of steering arms using these methods. First, I'll print and then secure them in place using epoxy. To assemble, I used ultra long ball joints and a 12mm button screw from underneath into the outside hole. A regular...

Low material use, low material waste I didn't like any of the other designs that seemed like overkill, big waste of material, so I made a frame that just keeps the upper module from moving around when you're gaming like a little freak This...

Instructions Using the following options: Build_Plate_Type = 0 Build_Plate_Manual_Width = 100 Build_Plate_Manual_Length = 100 center_radius = 12 element = Mg font = write/orbitron.dxf font_depth = 2.5 mesh_resolution = 70 pin_cap_gap = .45 ...

<p>Customized version of <a href="https://www.thingiverse.com/thing:114247">https://www.thingiverse.com/thing:114247</a></p> <p>Created with Customizer! ...<a...

I installed a new antenna, but the direct soldering kept causing it to break, so I created this protective mount to prevent further damage. To attach it, simply use the rear two standoff screws. ... Print Settings Rafts: No Supports: No Resolution: 0.1...

Remix of the very nice Critters's Part as to be used with M3 Nuts instead of Inserts. Small bracket is the original, big one is modded. Prints very easily in ABS 0.10. ... Thanks again to critters easy way to insert the M3 Nut: ...

Human: Customized version of Thingiverse Thing #114247 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=114247 Instructions Using the following options: ring height...

All rights are reserved by Berend JozefMoes. Visit www.berendjozef.wix.com/eternalflower for more information. ...The formula behind this geometric design is copyrighted, so consult with Berend Jozef Moes at berendjozef@gmail.com before utilizing any...

A personalized version of http://www.thingiverse.com/thing:114247 was created using the Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=114247). ...The specifications used include a pin cap width of 4, U as the element, a ring...