land rover discovery 1 3d models
899813 3d models found related to land rover discovery 1.cults3d
This is a Land Rover discovery 1 outside door handle and it works on both front and back door also if you need to the other side just mirror the part and thats it printed in apollox but any strong filament will work, i used apollox because it as a...
thingiverse
For Land Rover Discovery 1 fans/owners. How to repair the switch for right front chair. You can find other info at https://forums.lr4x4.com/topic/47674-how-to-repair-discovery-electric-seat-switches/ . ...
thingiverse
For Land Rover Discovery 1 and 2 It works on either side of the car. PRINTING Print the body with the flat side level with the bed. Print the clip with the prongs facing up. Print the cap with the tube facing up (for me this piece was a tight...
thingiverse
These hold the door cards for all four passenger doors and the rear door card into the door metalwork on Land Rover Discovery 1 200tdi and 300tdi (these both say tdi on the back) and I think also the TD5 (which does say TD5 on the back) and on the V8...
thingiverse
Replaces the ashtray and/or coin tray in a discovery 1 and 2. Carling switch holder: Holds 3 carling switches. Dual socket holder: Holds 2 sockets/meret plugs/usb/ect. ... Blank: Just a blanking piece, drill what ever hole you like in it.
thingiverse
I remixed the blank piece provided to hold a 52mm gauge because we all know the rovers could use an accurate oil pressure or coolant temp gauge. it can be a little hard to see if your gauge has a super sunk in face. ...and you will need to trim some of...
thingiverse
You WILL need to modify your rover for this, trimming out a bit of the stock "mating flange" for this piece, including where the stock mount goes. It is designed to be screwed in with some small countersunk screws instead of using the stock clips as...
thingiverse
Model will be sent to the mail that deposits 50 dollars to my paypal account. (Paypal : naziferbay@gmail.com) for 20x20x20 table size. ... https://youtu.be/29Dd0Lb76XM
thingiverse
After both sides of my hood latch handle breaking off, I designed this handle to slip over the remainder of the handle. I have had it on the car for years and it works great. ...I printed out of black PTEG
thingiverse
Window buttons support I used ME screws to fix it to the mirror already posted here(https://www.thingiverse.com/thing:4155561) on thingiverse. ... I recommend the use of PETG
thingiverse
I found that the eyelets that hook to the back of the vehicle to keep the parcel tray (blind) closed had broken through, so I designed a workaround... I printed these prototypes from PLA at 0.2mm layer height but will re-print them at 0.15 in...
thingiverse
The headlight clip which breaks a lot - two screws go through the holes forward to the headlight, the socket pops onto a 8mm ball protruding from the headlight adjuster. ...Three of these support each headlight unit.
thingiverse
These replace broken cracked original brackets, the dimensions are very close, fit is great. I printed mine in ABS (about 5hours+) full support needed to support the middle cross section and internal hollowing. Painted mine to protect from UV rays...
cults3d
Rim for 1/10 scale for RC models similar to Land Rover Discovery 1998-2001. ... HEX 12mm (standard for RC models), 1,9" size The cover with the bolts can be set in place with double sided tape.
thingiverse
I wanted to install a GPS equipped stereo in my Land Rover Discovery 1, I also didn't want to cut any dash parts to make it fit. I installed the stereo by using the original stereo steel frame and extended it with some steel plates and rivets. This...
thingiverse
This is the plastic clip for the back of a headlight for a Land Rover Discovery 1, the geometry is the same on the Discovery 2 so it should work fine for that too.
grabcad
snorkel for Land Rover Discovery.Pre-cleaner is accurate. ... Tube is best guess.
3docean
renders Are made in 3ds Max 2008 using vray 1.5 (studio environment is not included in the set) If you need any other formats we are more than happy to make them for you. We greatly appreciate you choosing our 3D models and hope they will be of...
3docean
renders Are made in 3ds Max 2008 using vray 1.5 (studio environment is not included in the set) If you need any other formats we are more than happy to make them for you. We greatly appreciate you choosing our 3D models and hope they will be of...
grabcad
Camel Trophy style Land Rover Discovery winch tray for Superwinch Husky
thingiverse
Remix of original cup holder for Land Rover Discovery 2 (https://www.thingiverse.com/thing:2451722). Fits Discovery 1 also. I have removed phone holder since I didn't need it and also increased diameter to fit bigger mug (~75mm inner diameter). ... ...
thingiverse
This blank fits within the Land Rover Discovery 2 stereo space, roughly matching the dash curve. The "pin" can be glued into the metal bracket, allowing the face to be screwed in securely. ...There is a shelf in the back which can be glued to a tray as...
cults3d
here is a gallery for a land rover discovery the bodywork comes from jsscale the gallery does not need screws to fix to the body, no need to drill the body it is composed of the frame of the gallery and several hoops there are also supports for a...
thingiverse
I helped out a fellow 3D printer with a quick design to protect the indicators on the Land Rover Discovery (in this case a TD5) I've not printed this or tested the fit, but feel free to give it a try. (I suggest test fitting it before drilling any...
grabcad
Caisson amovible intégrant un emplacement pour table et tabouret, 1 grand tiroir et une kitchenette !Idéal pour les baroudeurs :-)
3docean
renders Are made in 3ds Max 2008 using vray 1.5 (studio environment is not included in the set) If you need any other formats we are more than happy to make them for you. We greatly appreciate you choosing our 3D models and hope they will be of...