landing leg 3d models
75472 3d models found related to landing leg.
thingiverse
Center landing leg for mini quad, ads extra support. ...will require frame modifications
thingiverse
On my first flight I crashed the drone and nearly snapped off the landing leg. ... This was made to replace it, once it finally dies!
thingiverse
Near-1:1 scale with Estes Outlander - reduced 10% (in Cura) before printing, for better fit to 1:1 scale landing legs. I printed all 8 struts on glass, with 4 of the 8 flipped to the opposite side. This achieves a smooth outer surface for all 8...
thingiverse
Generic landing legs designed for khanindustries fantastic elite dangerous ship models. Main landing leg can be mirrored for left or right as desired. These were designed to fit Krait Mkii. Edit and scale as required. I used support for under the...
thingiverse
Landing Legs for the QR400 Quadcopter with aluminium arms.http://flyduino.net/QR400-FPV-klappbarer-H-Quad-Set-GFK-PCB-Aluarme You need also four 5mm carbon rods. Just snap the landing leg on the copter arms. ... Print Settings Rafts: ...
thingiverse
A replacement Landing Leg for DJI F550 Drone. Same leg is used on the F450, i think. The original legs are designed to brake so I modelled this based of those. Only with two holes for mounting. ...Suits my project!
thingiverse
here are alternative landing legs to maulwurfpaulis design. i added nuttrapps and a bit bigger hole for the landing leg rod. the nut is for a more secure thightening. i myself use aluminum legs so i heat them up and force them in after. you can print...
thingiverse
Just a simple landing leg for the DJI Spark. It can be used with or without the Prop Guards. ...Total weight for four is only 9 grams with 20% infill.
thingiverse
... on its side if not careful. ...Resolution: Add Landing legs to the quad just below the motors that are tall enough to allow the battery to be elevated from the ground. ... Provides level base for quad to take off from with minimal weight impact.
thingiverse
A drone landing leg that doesn't suck :-) Cool feeling, easy to mount. Print Settings Printer Brand: RepRap Printer: ...
thingiverse
This is a "landing leg" created to help support multi-rotor UAVs which use 10mm carbon square tube as motor arms. There are holes to allow the attachment of two 3mm zip ties. Each leg weighs ~7.3g (assuming 100% infill, PLA). Print Settings Printer:...
thingiverse
I wanted to remix the Landing_Leg with some in-model support to help get my success rate up above single digits. Jared kindly uploaded the STEP files for his Falcon thing on request. I hope this will help anyone having trouble like I was...
prusaprinters
A drone landing leg that doesn't suck :-) Cool feeling, easy to mount. Print Settings Printer Brand: RepRap Printer: 3dRagRafts: No Supports: YesResolution: 0.2 Infill: 40% or more Notes: Tested in PLA, works fine. I'd like to try HIPS for this...
thingiverse
The flows from snowboarder1337's improved FlameWheel arm, which offers greatly improved strength but is no longer compatible with the landing legs in the original project. Here are two landing legs (of different sizes) which are compatible with...
thingiverse
This landing leg was developed for my son who had a tendency to break them often. These legs are strong and secure but if you do break one they can be replaced in seconds. ...The leg loop clips in to the base
thingiverse
These landing legs use nylon ties to attach to the 1/2" booms I use on my multi rotors. I have only broken one and it was a crash from about 15 feet up. Typically, the nylon tie will just break and you can replace it with a new one. ... ...
thingiverse
Landing leg for X class drone/quad-copter. Hole to hole spacing for 1 clamp is 31 mm. This is used with aluminum clamps and 25 mm carbon tube. Included is the .stl and the Solidworks file if you wish to change it. ...I recommend printing at an angle for...
thingiverse
Model of the SpaceX Falcon 9 Landing Leg, Print out four of them for a complete set, meant to compliment the model rocket found on the store which lacks them. Or use it as a book holder idk. ... Forewarning: it doesn't match the outline on the model...
thingiverse
My friend asked if I could make a bit stronger landing leg for the MHQ2. I added a radial hoop between the feet that still allows it to be flexible but changes the load path enough to make the the braced corner not snap easily. Adds 3.3 grams each...
thingiverse
Simple legs install on the bottom plate. ...Assembly with 2 screws by side with the precut holes of the frame
thingiverse
A 3D printable leg for my Quadcopter. ... Parameterisable in the SCAD file, just change the values at the top and export.
thingiverse
Keep your DJI Spark out of the grass with these snap-and-slide on landing gear. Only adds 12 grams to the weight of the Spark. ...Just clip it on at the motor and slide it towards the body.
thingiverse
I did a simple remix to add more support to the legs, and try to make them look more like the hydraulic supports on the actual Falcon 9. ...Made using the 1:96 scale.
thingiverse
Printed in Nylon (excuse my terrible print quality, still learning the nylon) I tried this with ABS, but they mostly shattered on the first hard landing. The nylon seems to be getting similar nice, bouncy performance to the huge bent up zip tie I was...