laser printable post it notes 3d models

A sticky note holder. Holds 3x3 paper. This was designed for 3mm wood. I used birch ply. ...The flamingos have some very thin cuts, so I flipped the finished pieces over so the cleaner bottom cuts are on the outside.

Simple post-it dispenser for pop-up style notes.

post-it notes holder 96 x 98 x 79,9 (mm)

This is a work desk Post-it notes holder for better organization of your desk. ...I also added a pen holder.

2 post-it note holders for 76mm by 76mm & 38mm by 51 mm sizes They can be printed without support, by flattening the base to the bed of the printer, but it will produce a stepped effect on the top as you can see in the photograph. ... **UPDATE**:...

Sticky notes / Post-it holder. ...10 slots.

Post-it Notes Desk Dispenser for 3 x 3-Inch Notes

Boxes designed to hold a dozen 76x127mm, 76mm by 76mm or 38mm by 51 mm post-it notes **UPDATE**: There maybe a problem with printing the 12 large post-it notes box. ... If this happens then use the updated version.

I made the back solid to decrease print time and make sticking it to surfaces easier. ...I also enclosed one end so the post-its don't slide through

This is a dispenser for the Post-it Popup notes that fanfold out. ... As always, if you make it, I'd love to see pictures!

This is a dispenser for the Post-it Popup notes that fanfold out. ... As always, if you make it, I'd love to see pictures!

Designed for specifically 3M post-it notes and sharpie pens, I think they are really good together. ...But the hole is pretty wide so you can use it with any other pen.

I just rebuilt my office and needed something to house some sticky notes (aka post-it notes) and a book of 5 book sticky tags and here it is. It fits a book of sticky notes (75mm x 75mm and 40mm high) and a book of 5 sticky book tags (73mm x 49mm) -...

Summary This is a dispenser for the Post-it Popup notes that fanfold out. As always, if you make it, I'd love to see pictures! Print Settings Printer: Creality CR-10S Rafts: Doesn't Matter Supports: No Resolution: .2 Infill: 10% Notes: Printed with...

Just a simple dispenser to insert 51x51mm M3 Post-it Notes. ...Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 100% Notes: 3mm Thick How I Designed This Sketch Up

This key chain is made for holding a small size Post-it notes pad and a shortened pencil. ...So you get both always at hand.<br><br>Prototype was printed using 0.3mm layers with support enabled.</p>

I remixed this, as i use the smaller 1.5" x 2" post-its.

Measures: 172mm wide x 100.5mm deep x 100mm high Can hold standard sized post it notes (76x76mm). Business cards (lying horizontally up to 87mm long). Or put your phone in there (thanks to my girlfriend for pointing this out). Bunch of pens and...

Here is a small desk organiser that I have made it can hold a stack of stick notes, a few pens/pencils and 6 usb fashdrives.

I Re-mixed my Re-mix to correct a few things i didnt like about the original file, i have upped the size by 1/4" and made it sit taller by 1/4" to allow for the added height of the post-its.

Post-it Note holder holds 2" Notes.

can hold 4 post-it notes (77x77)

Post-It Note stack for Min352

Just a simple post-it note holder.

Two post-it note holders for different size note pads

Post it holder, it fits up to 75mm square post it notes. ...

A simple post it note holder. ...Made with 8 different slots.

Simple Timber Post-it Note Holder design modeled and assembled in Creo Parametric 2.

This is a tower I made because I have too many post it notes.

was made for a friend as a post it note tray in his office