latrax teton custom body 3d models
1216289 3d models found related to latrax teton custom body.thingiverse
Latrax Teton 1/18 scale r/c car control arm, simple design but works great
thingiverse
The Latrax Teton bumpers have holes that will accept 3mm led, but no holders. So I came up with these brackets to hold them. ... The front buckets will hold two 5mm leds for added light.
thingiverse
This is a roof rack I designed for our Latrax Teton 1/18 scale trucks. I obviously customized ours with our names. If your name is Mike or Kim I would be happy to send you the file. I printed this on our Creality 10s. The hardware I used are18-8...
thingiverse
Customized version of https://www.thingiverse.com/thing:4099230 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4099230
thingiverse
... a CodeBlocks and parametrized the model, so I could change any dimensions easily. They are much harder to mount than stock tires, so you need to use tools like screwdrivers or something. Upd: Redesigned in OpenSCAD with default values for Teton
thingiverse
... on sale work light. 2 LEDs in series with 100 ohms of resistance worked well with a 9v battery. I zip tie a 9v battery to the rear body mount and use a 9v connector as my on/off switch. ... You could probably choose to do something more elegant.
thingiverse
Latrax Preeti Runner/Latrax Rally/Latrax Teton shock guide. ...
thingiverse
## Links: * [LaTrax Teton](https://latrax.com/products/teton) * [3M Super Strength Molding Tape, 03615, 7/8 in x 5 ft](https://www.amazon.com/3M-03609-Scotch-Mount-Molding-Tape/dp/B000BO9L00?th=1) * [ENGPOW 7.4v 2200mah 25C Lipo...
thingiverse
I thought the Teton would look cool with a spare tire on the back. ...Also incorporates my led buckets.
thingiverse
Instructions I picked up a take off steering linkage for a Teton off ebay and that had most of the hard parts to complete this swap. You also need a set of front knuckles and hubs along with a few ball studs. A little dremeling is required to...
thingiverse
this part is to replace the wheel hexes on the latrax prerunner and teton.
thingiverse
Traxxas (LaTrax) Teton ESC and FAN cover. I upgraded the motor on my Teton to this Hobbywing combo and designed these parts to use with it. ... https://www.hobbywingdirect.com/products/ezrun-1-18-bl-system-combo?variant=214163984 .
thingiverse
My son broke one of the steering blocks of his Latrax Teton so I recreated it in Blender. I made it a little beefier so hopefully it won't break. I used a 3.5mm drill bit to clean up the hole that goes through the two arms so it moves easily...
thingiverse
... in PLA at 0.1mm layer, 50% infill. Tolerances may need to be adjusted, as the one I printed was a tight fit. I feel the bumper of the Teton on itself is too flexible, adding a lot of vibrations to the video, please keep that in mind. ...Enjoy!
thingiverse
Customized version of https://www.thingiverse.com/thing:4099230 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4099230
thingiverse
Here's an easy way to obtain a set of wheels that will allow you to drift your RC LaTrax Teton or Prerunner. These wheels work very well with the brushed (stock) setup. It is quite easy to hold a drift when running on any hard surface. It is also...
thingiverse
this is a guard for the rear body of the latrax prerunner, it isn't really needed but it helps if you are going to be doing wheelies if you overvolt it and you don't want to ruin the rear of the body
thingiverse
I designed these wheels to have more grip in the snow. For a quick test run I printed these without any infill. You can improve these wheels by using some infill of your choice ;-). Please let me know what works best for you. ... You should mirror...
thingiverse
I made these body posts to mount a Dromida Wasteland Truck body to a LaTrax Prerunner chassis. ...It would probably work on other LaTrax ground vehicles because I believe they share the same chassis.
cults3d
I made these body posts to mount a Dromida Wasteland Truck body to a LaTrax Prerunner chassis. It would probably work on other LaTrax ground vehicles because I believe they share the same chassis. ... See it in action:...
thingiverse
This should stop the Mounts on the bulkhead from breaking. ...It will flex a bit to allow some shock absorbance.
thingiverse
Here are custom trim knobs for the Traxxas & La/Trax TQi remotes. ... 1. Throwing Star 2. Karma Sun. They look awesome when coupled with the custom steering wheel.
thingiverse
Latrax Rally shock tower adapter for Udirc body V.1 Edited to mount UDIRC SG-1601/4 body 1/16: Lancia Delta HF Latrax Rally hex adapter 12.6mm to 9mm. Spacer 8mm Edited to mount UDIRC SG-1601/4 tire 1/16 I apologize in advance for the lack of...
thingiverse
The only thing you will need is the 2mm pin that came out of the original driveshaft and another one that is about 9-10 mm long, for best fitment drill out the holes on the dog bone with a 5/64th inch drill bit. They rub on the diff cups a bit but...
thingiverse
Needed a different body configuration. ...Uses all of the other parts designed by Cornly_Cool
thingiverse
This is a 3D topographical map of the Grand Teton and the surrounding peaks of the Teton Range in western Wyoming. ... Created using Thatcher Chamberlin's awesome tool, Terrain2STL.