lazy susan turntable 3d models
8677 3d models found related to lazy susan turntable.thingiverse
I made a double tier lazy susan using dollar tree plates and glass and needed low profile (less than 9mm high) lazy susan turntable. It was designed to fit inside the recess on the bottom of a dinner plate. It uses 4.5mm bb's for the bearings. Add...
prusaprinters
I made a double tier lazy susan using dollar tree plates and glass and needed low profile (less than 9mm high) lazy susan turntable. It was designed to fit inside the recess on the bottom of a dinner plate. It uses 4.5mm bb's for the bearings. Add...
thingiverse
I needed a lazy Susan face bearing for a cosmetic carousel that I found on instructibles.http://www.instructables.com/id/Cosmetic-carousel/ Update 5/15/18 Reorianted Base and Pad to remove the requirement to flip over to print. Curious... This seem...
thingiverse
A small turntable I made for spray painting. ... For use with a 6211-ZZ 55mm x 100mm x 21mm bearing, such as this: https://www.bearingboys.co.uk/Dunlop-Ball-Bearings/6211ZZ-Dunlop-Shielded-Ball-Bearing-55mm-x-100mm-x-21mm-2032-p
thingiverse
This is a "lazy susan" turntable bearing using cylindrical 1/4" spacers instead of spherical ball bearings. A single screw with a washer can be placed through the center recessed area to attach it, and also hold the bearing together. (Additional...
thingiverse
Attaches a NEMA 17 stepper motor to a rotating base. ...It is made for a stepper motor with a 4.5mm D shaft.
prusaprinters
<p>Attaches a NEMA 17 stepper motor to a rotating base. ...It is made for a stepper motor with a 4.5mm D shaft.</p>Category: Art Tools
grabcad
Lazy Susan bearing, zinc plated, 1000lb capacity acquired via Amazon. ...All dimensions collected with direct measurement of my example so manufacturer tolerances may vary your result.Final dimensions roughly 12" by 5/16"
thingiverse
Remixed MarvinPunds nice turntable design for use with the very common 608 bearings (the ones that are used on skateboards amongst other things). It should be a nice tight fit on the bearing. The outer diameter is 76mm if it were a full circle. ... ...
thingiverse
3 part press-fit lazy susan turntable using standard 6mm airsoft BBs as the bearings. This rolls very smoothly, but make sure to fill the entire bearing housing with the maximum number of BBs that will fit (this is scaled to allow for appropriate...
thingiverse
Oh yeah, I forgot to mention what makes this project different: Unlike other 3D turntables on the internet, this one incorporates a cheap store-bought Lazy Susan that can be connected to the motors by just placing it onto the stand. The gears click...
thingiverse
Additional mount for office wall 22,4 mm
thingiverse
This remix integrates a 52mm ID ring, and creates a 45mm hollow shaft, to allow the Hamilton Beach 32100 food dehydrator to blow hot air through the center. I've included another adapter version, with 80mm center to center hole spacing. Measure...
thingiverse
The base (under the bearing), and the main rack (over the bearing), are recessed with a 95mm wide square cutout, that centers the turntable bearing. You'll need to print these pieces together, for one complete unit: - 300mm print beds: Base +...
thingiverse
Hardware needed: Geared motor(3rpm is good for this use): https://goo.gl/nBgrtR 8x AA battery holder: https://goo.gl/cEtUpb Toggle switch(not exact same, but cheaper!): https://goo.gl/UwNQZJ Turntable video:...
cults3d
Hardware needed: Geared motor(3rpm is good for this use):https://goo.gl/nBgrtR 8x AA battery holder:https://goo.gl/cEtUpb Toggle switch(not exact same, but cheaper!):https://goo.gl/UwNQZJ Turntable video:https://www.youtube.com/watch?v=hffyPaDBvPw...
thingiverse
I couldn't believe how much it cost for a lazy susan that fell to bits when I took the shrink wrap off, has to be carried very carefully and sticks badly once every revolution, so I bought my first ever 3 inch lazy susan bearings from Quality...
myminifactory
Hardware needed:Geared motor(3rpm is good for this use):https://goo.gl/nBgrtR 8x AA battery holder:https://goo.gl/cEtUpb Toggle switch(not exact same, but cheaper!):https://goo.gl/UwNQZJ Turntable video:https://www.youtube.com/watch?v=hffyPaDBvPw...
thingiverse
snap together thrust and turntable bearings using airsoft 6mm. ... five versions. -50mm thrust bearing with 20mm center hole -50, 75 and 100mm turntables 100mm 'lazy susan' (turntable with screw holes in both plates). ...
thingiverse
Here is a 115mm diameter Lazy Susan which should easily take a 250mm serving plate. All you need are x5 16mm ball bearings or marbles. Print this off, put it in the centre of your table and place a plate of fancies, Hors d'oeuvre or canapes; which...
thingiverse
210mm diameter turntable designed to print within bed of Ender 3 pro. Requires a 608 bearing between the base and top. The honeycomb perforation is intended to let air and paint flow through so as not to deflect back up onto the model. The collars...
thingiverse
This is an all plastic bearing using 6mm AirSoft BBs Instructions The holes may need a bit of reaming since the 6mm AirSoft BBs seem to have missed all but cursory QA... ...just open up with a 6mm twist...
thingiverse
To save some space around my printer I bought a cheap 30cm(12") turntable (lazy susan) and placed it on top of my delta frame (Anycubic Kossel Linear Plus). I designed these parts to hold the turntable in place. I bought the turntable "AsiaLONG 360⁰...
thingiverse
3D printable spur gears, motor housing, and stands that mount to a 4" Lazy Susan Turntable Bearing and a 110V 33-39RPM synchronous motor. ... 4 - #6 X 1" bolts 4 - 1/4" X 1/2" bolts 12" wooden circle
thingiverse
It uses a 6" Lazy Susan as a base, the one pictured was from https://www.homedepot.com/p/Everbilt-6-in-Square-Lazy-Susan-Turntable-with-400-lb-Load-Rating-49548/203661089 It is attached to the base with M3 screws, washers and nuts. ... The tapered...
thingiverse
# Parts List This project is designed to use the [6" Lazy Susan Turntable from Amazon](https://www.amazon.com/Triangle-T6LS-Square-Lazy-Susan/dp/B0006LBVDS/) using a small ish number of 3D printed parts. It is assembled by M3 bolts that use...
thingiverse
Please refer to the video for instructions: https://youtu.be/Ko4hd_iNnEM Parts List: Gear Motor (12v 40rpm/Package A) https://s.click.aliexpress.com/e/_DCOmEpB 2GT Pulley (20TB8W6) https://s.click.aliexpress.com/e/_Det2hGH 2GT Timing Belt (400mm)...
thingiverse
A small Lazy Susan I plan to use for table games and such. Top is 210mm and barring is 608. ...Added gripping mat for the base and a carbon fiber paper to the top.
thingiverse
Was looking for a Lazy Susan to work with my kinect to 3d scan. I couldn't find one that had angle marks so I designed one. Requires 5 - ZZ809 Bearings. ... Edit: Top was not stable so made an inner ring to stabilize it.