lcr t4 case assembly 3d models

Attach Dupont Connector Pins (Male) to the DIY SMD Clamp. ...Connect wires to these pins to create a Meter Lead Probe for use with LCR-T4 IC Testers and other devices.

This project calls for a custom design of the LCR-T4-module. Initially, I tried using cases from Thingiverse, but they didn't meet my expectations. ...As a result, I decided to create a case that perfectly accommodates a 9V battery.

Designed for LCR T4 chinese clone (yellow PCB and a button in right bottom side). The battery compartment is located on top for easy access and quick battery disconnection e.g. to reset device. I used 6 additional screws 3x6..12mm. ...May be...

Designed for LCR T4 chinese clone (yellow PCB and a button in right bottom side).The battery compartment is located on top for easy access and quick battery disconnection e.g. to reset device.</p><p>I used 6 additional screws 3x6..12mm. ...May be...

Special design for the LCR-T4 ESR meter from Tayda Electronics http://www.taydaelectronics.com/new-arrivals/esr-meter-transistor-tester-lcd-diode-multimeter-capacitance.html A 9V battery holder is held in place by friction, and the pcb installs with...

It's case for LCR-T4 ESR Meter with two additional section for battery (9V) and 3 wired connectors that closed sliding dovetail lid It's needed 4 screws 3x25 It's was ordered here https://www.aliexpress.com/item/32797743484.html

The case is made to protect the microcontroller from the discharge of capacitors. ...Thread 20X3 mm.

I created this case for my LCR-T4 tester to make it rechargeable, thus avoiding the use of those pesky 9V alkaline batteries that don't last very long. The top compartment of the case fits an 18650 battery, a 03962A USB charger, and a boost...

The body of a well-known transistor tester. It has room for a modified transistor tester with an encoder, battery pack, TP4056, and MT3608. ...https://letyshops.com/r/aliexpress-3cxm8cqywveok Tester https://letyshops.com/r/aliexpress-3cxm8cqyu8u8w...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Housing with lid-stand for component tester.The device can be installed at different angles or completely closed.When the lid is closed, the power circuit is interrupted.A resistor is provided on the front panel to discharge the capacitors before...

This scenario matches a Type 4 configuration with a blue button. A Type 4 setup featuring a yellow button would be an ill-fitting solution, in my opinion. ...I've reprogrammed the device using its original German source code and added features to...

Tester tranzystorów i RLC LCR-T4

Electronics Test Equipment Housing

LCR-T4\nI've made it just for you.

Bill of Materials: 1x LCR T4 tester PCB 4x 2.5x6mm screws for PCB assembly 1x XT60 male connector 1x XT60 female connector 1x Vigan 24.102.4 - 2 mm diameter panel-mount socket GREEN (or similar type) 1x Vigan 24.102.3 - 2 mm diameter panel-mount...

Here is the rewritten text: A human-built device quickly stands for an LCR-T4 transistor tester and battery, featuring a display mask.

LCR - T4 (Transistor, Capacitor, Resistor, etc.) Tester case with the addition of a separate opening compartment for a 9V battery type 6F22. It is recommended to position the parts when printing as indicated in the 6th image and use supports if...

The case splits into two parts - front and rear - making it easier to install the LCR-T4 tester before snapping on both sides. Four short M3 screws (I used M3x6) secure the component tester in place. Two shorter M3 screws (M3x10) hold the front and...

A 3D printable enclosure for **LCR-T4 12864** component tester, with a 9V battery compartment. Unfortunately, I had to cover the the SMD area, but it would have made the design more complex. Print `component-tester-box_box.stl` for the lower...

This is remix of https://www.thingiverse.com/thing:2999383 LCR tester model: LCR T4 (PCB dimension: 60mm x 72.6mm) BoM: 1x LCR T4 tester PCB 4x 2.5x6mm screws (for PCB) 1x XT60 connector male 1x XT60 connector female 1x Vigan 24.102.4 - 2 mm diameter...

This is remix of https://www.thingiverse.com/thing:2999383 LCR tester model: LCR T4 (PCB dimension: 60mm x 72.6mm) BoM: 1x LCR T4 tester PCB 4x 2.5x6mm screws (for PCB) 1x XT60 connector male 1x XT60 connector female 1x Vigan 24.102.4 - 2 mm diameter...

My LCR-T4 Component Tester was cumbersome without an enclosure, so I designed this. It's not perfect, but does the job for me. I wanted an angled enclosure but retain access to the battery when needed. I didn't want to use supports for printing or...

This is a low-profile tilting stand designed specifically for the affordable transistor tester known as LCR-T4, M-Tester, Mega328, and possibly some other names. It's engineered to work seamlessly with the most popular acrylic cases for this...

My LCR-T4 Component Tester was cumbersome without an enclosure, so I created one to make it more manageable. It's far from perfect, but it does the job for me and that's what matters. I wanted a sleek design with an angled angle, but also needed easy...

**Post Your Make!** This is the ULTIMATE box for the LCR-Tx component tester, based on Phenomen's work: https://www.thingiverse.com/Phenomen. I got tired of all the versions and remixes... wrong size, wrong windows, support needed, exposed...

A compact redesign to accommodate SMD components safely. ...The casing is engineered with a smaller opening to prevent SMD parts from slipping away.