leaf blower with gutter attachment 3d models

Customized version of https://www.thingiverse.com/thing:4636419 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4636419

Customized version of https://www.thingiverse.com/thing:4636419 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4636419

Wall hanger for Makita leaf blower model DUB362Z

Replacement Part for a Ryobi Leaf Blower Check out this link for the Tinkercad design: https://www.tinkercad.com/things/7wj7B041Vo6-blower-part-6 The screw hole thread isn't perfect, but heating up the screw on your leaf blower will cause it to...

This is a second handle for the EGO Power+ leaf blowers (only tested on the LB6500 but I believe it would fit the other similar models too). I found that, especially with the big 7.5ah battery, the blower is very hard to hold for a long time. Even...

I built a small guttering attachment for my dad's greenhouse, and I'm attaching it here. The outer diameter is 21mm, which means it will snugly fit into a PVC or Copper tube with an inner diameter of 22mm. ...Feel free to modify this design to fit your...

I was tasked to create a replica part to replace broken worn out pull handle on a leaf blower.

Customized version of https://www.thingiverse.com/thing:1848038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1848038

Simply wall mount that should work for most EGO Leaf Blowers. Designed with 3mm holes for screws. ...With the additional walls you should be able to thread through them for a strong hold.

Designed this to replace the Nozzle for the EGO leaf blower. ...I designed it to be print with ASA, so you might need to adjust it, since ASA have more shrinkage.

Galactic Ranger blasts off into outer space using a high-tech leaf blower backpack that propels him at incredible velocities, allowing him to soar through the cosmos like a superhero. ...With his trusty blower, he conquers the vast expanse of the...

This custom nozzle attachment fits perfectly on the DeWalt 20V Leaf Blower (specifically, this model: http://amzn.to/2tVWgnp). ...I discovered that the original tube was too bulky for navigating tight spaces and corners, so I designed a customized...

a nice little hanger for your craftsman leaf blower. ...Make sure the hook on the bottom is unfolded.

There are four files attached: 1 - Blower fan using the original nut 2 - Blower fan using M5 nuts for those who cannot remove the original nut 3 - Blower fan using the original nut with an additional outer support ring, ideal for PLA prints 4 -...

Summary Needed a different leaf blower nozzle for cleaning my driveway that would fit my Ryobi Backpack 40V leaf blower. I found one that looked like it would fit (made by 3DPossible) but, due to a taper on the Ryobi blower tube, the end that...

Replacement Part for a Ryobi Leaf Blower Tinkercad Link: https://www.tinkercad.com/things/7wj7B041Vo6-blower-part-6 The Screw Hole Thread is Not Quite Right, but It Will Re-Thread If You Heat the Screw on the Leaf Blower. ... I Included the Tinkercad...

I also added a ring on the inside edge to fit around the lip that is on the end of the leaf blower. This print is a tight fit. I did not want it blowing off the end. I printed mine with the Cura slicing tolerance set to exclusive. I printed with...

works good fits on Dewalt 60v leaf blower i have to trim bottom at a little angel but works amazing . ...I don't use rafts

A simple wall mount for the Greenworks 80V Leaf Blower. Modeled in Blender, and unfortunately messed something up along the way. So some of the "walls" aren't true "walls" (There's a term for it that I can't seem to remember). Meaning you'll see...

The Dewalt blower develops approximately 95 K/h (60 M/H) velocity, the 25% gearbox develops over 121 k/h (76 m/h) and the 50% gearbox develops over 150K/h (95 m/h)(tested with an anemometer). The reducers have been tested on #DCBL720B and ...

I designed this stubby nozzle for Scott Leaf blower, so I can maneuver easily when I'm drying my care. ...Designed and printed for ASA, so you might have a little bit slack if using other material

Designed to fit the Dewalt 60v Leaf Blower, like the one pictured. Fit is snug, but will keep it from blowing out. Remixed from the Dewalt 20v version, which had a slightly smaller nozzle. ...

I also used silicone adhesive to seal between the intake and cabinet, the output adapter and blower, and the exterior wall, with some expanding foam being useful for sealing gaps. ...The friction fit between the blower and intake seems sufficient, but...

Needed a new nozzle for my Husqvarna Leaf Blower. Mine is the 130BT model but I'm sure this would work for most Husqvarnas. It doesn't go over the quick connect tabs but it fits VERY snug over the tube. ...Sized for 70mm tubes.

I was always disappointed it only ever came with the one nozzle on the end of the blower called a “concentrator” but it's really more of a diffuser. I was equally confused why they made the nozzle removable but only had the one. If I'm blowing piles...

Bought a toy leaf blower ($10) at Cracker Barrel to use on keyboards and other electronics. Felt a quite of bit of air reversed out of the intake from the turbine blade. I work on motorcycles and searched for a carb venturi but none were exactly...

Wall mount for a Ryobi 18v blower

... I have included the STL and the OpenSCAD model for the part. Measurements were done with a caliper and are only approximate. But after replacement, it worked great. Blower Model: RY40403A (Should also work with RY40403) Motor Model: HM-312879001

This is an attachment for the Milwaukee M12 Spot Blower for inflating air mattresses. ...Due to the nature of the blower, it is not terribly efficient, but it does work well enough in a pinch.

Intergalactic Space Ranger blasts off on an epic quest to save the cosmos from evil alien invaders using his trusty Turbo Leaf Blaster, a high-tech hover device disguised as a garden tool!