leatherman signal mods 3d models
39763 3d models found related to leatherman signal mods.thingiverse
Replace the fire starter rod and safety whistle of the Leatherman Signal with a holder for one Leatherman bit. ...
thingiverse
This is a Remix of the Leatherman Signal Knife Thumb Stud. I took the measurements and optimized them a little... Also I changed the Design and made it more round and ergonomic. ... I hope you enjoy!
thingiverse
this is a replacement part for the leatherman signal whistle, with a working whistle. there might be a size issue' but just make sure the height is set to 4.2mm. ... after printing, check the fit and using epoxy glue, secure the parts and attach the...
thingiverse
Bit holders for Leatherman Signal. I tried some others that I found but ended up designing these from a blank sheet. Features include: 1. 1 bit storage in place of sharpener. Fits any size bit 2. 2 bit storage in place of whistle. Fits bits...
thingiverse
Replacement safety whistle for the Signal. Add a 42mm long (4.5mm diameter) ferrocerium rod to add the fire starter component to the part. ...
prusaprinters
... like shown in the picture below. ... This is slightly suboptimal though, because it means there is a weak point about 2/3rds up where the part can break easily. Other orientations with a bit more support material might yield better results…
thingiverse
Print a thumb stud for the Leatherman Signal. ... Press fit the part in place, or secure it with a drop of super glue.
thingiverse
Storage for the **Leatherman Signal** compatible with the Gridfinity system by [ZackFreedman](https://thangs.com/designer/ZackFreedman). Grid size: 1x3x3 Note that fitment was designed with the pocket clip installed. ... Depending on which side...
thingiverse
This mod is inspired by Yudi Irawan on FB Leatherman Tool User Group and based on danielhulbert's model on Thingiverse(https://www.thingiverse.com/thing:4165672). It would be impractical using the ferro rod to make a fire just to light up a...
thingiverse
*NOTE: WHEN PRINTING, ROTATE THE MODEL SO THAT IT SITS ON ITS SIDE WITH BIT OPENING POINTING UP (like in the pictures [not like the autogenerated 3D model]; makes the little alignment tab on the bottom stronger)* Bit holder to replace the included...
thingiverse
Customized version of http://www.thingiverse.com/thing:427373 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=427373 Instructions Using the following options: width =...
thingiverse
I took the real good Leatherman Signal Bit Holder from danielhulbert and added a holder for a pair of tweezers and a pen. ... WORK IN PROGRESS.
thingiverse
Customized version of https://www.thingiverse.com/thing:427373 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=427373
thingiverse
Inspired by Eric Au's designs on Shapeways (https://www.shapeways.com/shops/metro-qbranch?li=pb) This is a 3D printed hammer mod for the Leatherman Skeletool. I printed in 100% infill PLA and it seems pretty good. You will need a little threaded...
thingiverse
Inside the Signal there will be a smal PCB (8x8mm) with 3 LEDs (1.8mm from the outside edges, 1.8 mm Diameter), 3 resistors and a 3x3 mm connector. Challenge is to make this part precise enough. How I Designed This FreeCAD. ...Measurments from the...
thingiverse
Remix of aetheriusvoices, replacement bit holder. I diddnt have any extra bits so it wasn't particularly useful for me, and the stock sharpener is nice but also not super practical. The design I made allows for storing something small in a cavity...
prusaprinters
So I designed a mod for the leatherman free t4 to hold a Victorinox toothpick. It fits snug in the 3d printed part, and it is easy to assemble. You can buy the toothpicks very cheaply from a Victorinox dealer or online. ...To make it easier to print a...
thingiverse
Customized version of http://www.thingiverse.com/thing:427373 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=427373 Instructions Using the following options: height...
grabcad
3D model of a Leatherman multitool with pliers, knife, screwdrivers, can opener and a ruler in the handle
thingiverse
... to attach your Leatherman to your belt. ... Why? The normal wearing orientation means when sitting down the Leatherman is in the way and an irritation. Solution? Rotate it 90° ! Enjoy! ... "Mk2" is slightly curved to sit comfortably on your hip
thingiverse
Holster for Leatherman Utility Knife There are various sizes of the Leatherman Knife so verify the dimensions fit your tool. ... Fits Military Fatigue or boy scout type belts Approximate Inside Dimensions: 3.975" height 1.235" width 0.690" depth...
thingiverse
Holster for Leatherman Utility Knife There are various sizes of the Leatherman Knife so verify the dimensions fit your tool. ... Fits Military Fatigue or boy scout type belts Approximate Inside Dimensions: 3.0" - 4.5" height 1.235" width 0.670"...
thingiverse
... that goes with it. So with the assistance of the trusty leatherman, we have an attachment that is compatible with picking up the heaviest types of sushi. . Who would have thought? Plus you are also being sustainable in the process. ... Super Simple.
grabcad
This model is available for download at http://dan-herzberg.com/store/ The Leatherman Fuse multi-tool was released in 2004 and retired in 2012, and carried 7 tools. Modeled in SolidWorks by Daniel Herzberg in 2008. The SolidWorks file includes all...
thingiverse
Just my design of a leatherman stand/ case that will hold your tool when not in use. Can be mounted on the wall with command strips/ double-sided sticky tape as well. Another Idea I had was to 3d print it in glow in the dark filament, which would be...
prusaprinters
The normal wearing orientation means when sitting down the Leatherman is in the way and an irritation. Solution? Rotate it 90° !</p> <p>Enjoy!</p> <p>"Mk2" is slightly curved to sit comfortably on your hip</p> <h3> Print Settings</h3>...