leatherman thumb tabs 3d models

A simple holder for standard dishwasher tabs. ...Needs to be installed with double sided tape.

I replaced the glue-in tabs with simple friction fit locking tabs which seem to work fine, prints ok in both PLA and SLA. 

wouldn't let me remix original but yea this one doesn't have the bottom mounting hardware tabs aha enjoy!

When I came across this project, I knew exactly what I needed - my trusty Leatherman Bit kit still safely packaged to prevent any bits from getting lost. Initially, I thought slicing it and then resizing wouldn't make much sense, so I decided to...

The Leatherman Squirt fits tightly, so there is a cut-out on the bottom outside corner for your index finger to push the multitool out of the sheath the first couple centimeters. This exposes enough of the multitool to grab and pull it out from the...

This is a custom fit sheath designed specifically for the Leatherman Supertool 300.\nPrint Settings\nPrinter: Use an AO-101 printer to get optimal results.\nSupports: This model is fully supported by the AO-101 printer.\nResolution: Yes, this sheath...

the friction should keep it from moving at all. printed with .200mm layers, 20% fill, and 1.2mm shell. if you'd like to edit this in tinkercad please use the link below...

... to extend tabs outward. The number and size of these tabs are adjustable within the scad file. It is crucial to specify your telescope's outer diameter accurately so that the tabs fit perfectly; they will be generated beyond this specified diameter.

These tabs have been tested on my robot for the past 5 months (over the winter of 2017-18) and have been holding up better then the one that came with the chassis.This same tab should work with most brand of 2 layer acrylic robot chassis /kit,...

Corner tabs that help align glass beds on the heat bed of an ender 3. ...Could work for other bed types as well.

Check out this link for more information: http://www.domestichacks.info/2014/05/espektrum-dx6i-ersatz-trimmhbel/ Alternatively, you can also find the Spectrum DX6i trim tab replacements at this website. The link provided is:...

Remix of the base by ITSROBBY to add mounting tabs. The lid and all setting are the same. Refer to his model for lid and settings. ...

... To replace the dome light tabs, start by locating the headlight switch on the steering column. It's a lever that controls the lights. Locate the two small clips that hold the tabs in place. They are usually located near the base of the dome light.

Install a support bracket that holds stock firmly at a 45-degree angle, featuring detachable tabs for secure attachment to a workbench using sturdy clamps.

This versatile and portable Opener for tin cans with Pull-Tabs is perfect for use in the kitchen or on-the-go anywhere.

I discovered that the Qtrainer wing joints were vulnerable to damage, prompting me to design some straightforward attachment tabs for added structural support. ...These tabs not only improve the connection between the wings but also ensure precise...

Just implemented additional side holes and precision guide tabs into the current design.\r\n\r\nPrint at a 45-degree angle with a brim and supports in place on any sections above 46 degrees.\r\n\r\n2/27 - Expanded tab width slightly to ensure optimal...

Dimensions- Outside (excluding tabs): 6.125" (L) x 3.75 (W) x 2.08" (H) - (155.58mm x 95.25mm x 52.83mm)- Inside: 5.97" (L) x 3.54" (W) x 1.875" (H) - (151.64mm x 89.92mm x 47.63mm)- Overall Length (including tabs): 7.31" - (185.67mm)

I needed a few extra radio tabs to plug up the holes left by removing the factory radio in my NB Miata, but unfortunately, I only had enough to go around. ...To solve this problem, I decided to create a duplicate of one of the existing tabs using...

... that you can integrate on to mask models such as the Squid Game soldier masks. ... Use Meshmixer to align the mask tabs where you want, then boolean merge them together into one model for printing. ...Or print them separately and glue them on the mask

These replacement motor mount tabs are designed specifically for the Makerfire 4-wheel drive robot chassis, available on Amazon at https://www.amazon.com/Makerfire-4-wheel-Chassis-Encoder-Arduino/dp/B00NAT3VF4. ...After rigorous testing on my...

Dimensions- Outside (excluding tabs): 6.125" (L) x 3.75 (W) x 2.08" (H) - (155.58mm x 95.25mm x 52.83mm)- Inside: 5.97" (L) x 3.54" (W) x 1.875" (H) - (151.64mm x 89.92mm x 47.63mm)- Overall Length (including tabs): 7.31" - (185.67mm)

... PI camera has been remixed. ...The tabs were removed and a plan is in place to integrate it with another camera mount. This remix does not include tabs for screws, but it provides an opportunity for users to add their own as needed using simpler tools.

This model organizes the Leatherman bit kit and ratchet driver so that you can carry it in your pocket easily.It is a single file. I printed mine in Prusament PC blend with carbon fiber filament on a Prusa i3 mk3s+. Both bit kit cards need to be...

Wife got me a Leatherman Wave plus for my birthday, and I extended its capabilities with a bit that connects to 1/4" sockets. Printed in ZIRO blue PLA at 100% solid at the highest layer height you can do, I used .32 mm with a .4 nozzle. This is way...

My remix of the two best holsters for the leatherman wave plus, I decided to modify it because I need to keep the bits, the extender and the knife all together depending the situation so I decided to join the nice finnish of the holster and the...

... Then, print the "EDC Clip" by Bufftea, but you need to stop the print early so it's shorter like shown in the picture, the full clip is too wide to fit with the leatherman - just super glue it in place https://www.thingiverse.com/thing:2288554/files

This handy little spatula lets you hook your Leatherman OHT onto your belt securely, using a straightforward stiff clip. The accompanying images will guide you through attaching the spatula to the fabric pouch; you might need to use pliers to...

I made this TPU/Filaflex sheath for my Leatherman Multi-tool, but ended up using as a pen and screw driver holder. Size a bit small for heavy duty multi tools and too large for EDC sized. Feel free to adjust your scale! Its almost perfect for the...

This mod is inspired by Yudi Irawan on FB Leatherman Tool User Group and based on danielhulbert's model on Thingiverse(https://www.thingiverse.com/thing:4165672). It would be impractical using the ferro rod to make a fire just to light up a...