led 10 mm 3d models
575452 3d models found related to led 10 mm.cults3d
Imprimir con soportes en la guía de los leds, en Cura con soportes en zigzag al 15% salen perfecto y muy fácil de retirar.
thingiverse
Imprimir con soportes en la guía de los leds, en Cura con soportes en zigzag al 15% salen perfecto y muy fácil de retirar.
cults3d
LED Strip Stand for wide 10 mm 1. File LED Stand Start for set start of LED Strip rail with stand 5 mm lift the LED Strip rail not close to the ground and add an anchor point with a cable tie. 2. File LED Stand End for set end of LED Strip rail. 3.
thingiverse
LED Strip Stand for wide 10 mm 1. File LED Stand Start for set start of LED Strip rail with stand 5 mm lift the LED Strip rail not close to the ground and add an anchor point with a cable tie. 2. File LED Stand End for set end of LED Strip rail.
thingiverse
This is a LED mount for 10mm power LEDs. I used two of these in my robot car as headlight. ...http://dlacko.org/blog/2016/01/01/mr-stitson-robot-car-with-lego-platform/
thingiverse
Klammer für meinen Druckerschrank 10 mm LED Stripe höhe des Stripe 2.28 mm Schraubbar
thingiverse
For 10 mm LED light strips. Can be attached with a nail or a screw. ... Feel free to copy/modify do whatever you want ;-) ...
thingiverse
Holder for a 10 mm LED. The pin does not match the original fischertechnik dimensions. It is adapted for my Prusa I3, so it fits fischertechnik. Holder for 3 laser diodes 6mm Holder for a power LED heat sink Base plate 15x45 Instructions Please...
thingiverse
Customized version of http://www.thingiverse.com/thing:22006 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=22006 Instructions Using the following options: rows = 5 diameter = 8 cols = 10 height = 3
thingiverse
Simple 5 ring LED strip holder. ... In my case it'll hold the LED lights secured above my printer.
thingiverse
A nice LED STRIP support for 8 & 10 mm threaded rods & bars. ... Can be printed in a 200x200 bed diagonally.
thingiverse
A remix of the original "10 mm Slide-IN LED Strip mount for 2020" to work with 3030 profiles slot 6
thingiverse
- [WS2812b led strip](http://s.click.aliexpress.com/e/FyMPRmo), make sure you choose IP30 any other IP rating wouldn't make any sense and will not even fit.I would recommend buying a strip with 60 leds/m. ... ###### Affiliate Link above ### Get...
prusaprinters
A mount that clips into a T-Slot 2020 that allows to slide in any 10mm LED-Strip like the WS2812b. Print instructionsInspired by other designes but this one lets you slide in your LED-Strip into the print → no adhesive required → LED-Strip won't fall...
thingiverse
Lowered the footprint by putting the holein the middle, added indent for nail/screw head. ...Increased base to compenstate.
thingiverse
Basic remix of the source thing to clip onto and hold LED-strip-circuit boards of 10 x 1.7 mm. Uses the same holder as the original. ...Print Settings Printer Brand: Prusa ...
thingiverse
... strip itself, therefore I did a clip in design. the 20mm for the ticky tape is related to standard 3M sticky tape width. Have fun installing. The included twist in cable clips are handy if you want to also clip the supply wireds for the LED strip
prusaprinters
yet another LED strip holder. This time with a clip in design for 10mm strips with rubber cover IPx protection. ...I didn't want to use the sticky tape of the strip itself, therefore I did a clip in design. the 20mm for the ticky tape is related to...
thingiverse
Modified version of LilTrublMakr's LED clip to fit a bigger LED strip (10 mm wide, 50 mm length).
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=69655 Instructions Using the following options: Tool_Length = 10 Nut_Size = 10 Font = write/Letters.dxf DualExtrusion = Extruder1 ToolOptions = 2 kerf = 0.3 message = 10 mm
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47842 Instructions Using the following options: Tool_Height = 5 Nut_Size = 10 Font = write/Letters.dxf message = VIDAL 10mm Tool_Length = 10