led strip light casing 3d models
453052 3d models found related to led strip light casing.thingiverse
This is ARGB light bar for WS2812B LED strip, I designed it to fit in my SilentiumPC Signum SG1V PC case, but I'm sure it will fit many other cases. Light bar supports 33cm length LED strip that's up to 10mm wide. I used 30 led's/meter strip (so 10...
cults3d
This is ARGB light bar for WS2812B LED strip, I designed it to fit in my SilentiumPC Signum SG1V PC case, but I'm sure it will fit many other cases. Light bar supports 33cm length LED strip that's up to 10mm wide. I used 30 led's/meter strip (so 10...
thingiverse
We made a simple box for protection, its not perfect but it does its job Use a tiewrap or electrical tape to close, or be free to remix this design
cults3d
I bought a led controler on amazon, and I had the feeling that the strip connector was in a critical situation with nothing to hold it. Then I made this casing to protect the connector and held it in place. ... Printed in white PLA 0.2mm layers 4 wall...
thingiverse
Use to clip in LED strip lighting and attach to wall or other surfaces with 3M Command strips.
thingiverse
Accommodates 1cm wide LED strips. ...Also has STL for light diffuser.
thingiverse
simple mounting clips for two styles of led light strips commonly found on amazon.
thingiverse
Low profile LED light strip holder for my Ikea lack table stand Prusa enclosure
thingiverse
Clip to screw an LED light strip to the underside of a shelf or cabinet.
cults3d
Simple LED work light made of L aluminum profile and 12V LED strip. ... BoM: 1x 12V LED strip 1x aluminum profile L 30x15x2mm 2x M4 nut (self locking) 2x screw M4x8 DIN912
thingiverse
Simple LED work light made of L aluminum profile and 12V LED strip. ... BoM: 1x 12V LED strip 1x aluminum profile L 30x15x2mm 2x M4 nut (self locking) 2x screw M4x8 DIN912
myminifactory
LED strip light stand. Three point base and adjustable angle. Strip light screws to the stand using clips that come with the light. ... M6 hex head bolt 30 long & M6 nut .
thingiverse
Using LED strip (purchased from Amazon in my case) is a SUPER cheap way of lighting an enclosure. The double sided tape won't hold forever, so why not fasten it with a mechanical hold like this one. It is designed for a #6 wood screw countersink. ... ...
thingiverse
This is a holder for LED strip lights. The sticky backing on my lights would not hold and this resolves that issue. ...
thingiverse
LED light strip for the printers. Source code for controller: https://git.notfound.dk/mikkel/prnlight/ (requires a wemos D1 mini - esp8266 ) Printed in PLA Default settings in prusa-slicer. Can be extended a wide as you wish. Colors used:...
thingiverse
This is a cover for LED Strip Lights. It prints without supports. Looks good using white or clear filament. ... It has 4 holes for mounting using screws
thingiverse
This is designed to hold 5050 LED strip lighting. Its installed in my bathroom in my motorhome using glue. ...I've added clamps to mine so its tight.
thingiverse
My LED strip does not have the silicone so I filled the channel with silicone caulking after installing the LED strip into the housing. ...The housing has been made slightly deeper than the one shown in the picture to allow the center LED to sit fully...
thingiverse
... LED striplights that Banggood sell. ...The strip lights themselves are excellent, but the sticky pads they ship with are fairly hopeless. https://www.banggood.com/20CM-3_5W-Dimmable-16-SMD-5152-Super-Bright-Micro-USB-LED-Strip-Lights-p-969249.html
thingiverse
Helpful for mounting LED light strips (like these: http://tinyurl.com/o3uwmg3) after the adhesive backing wears off. ... Just nail or tack the mount to the surface and clip in the lights.
cults3d
I wanted to install LED strip lights in my camper and I did not want them falling down. The adhesive doesn't always stick. I use mostly the 270mm part and one end piece. I used a small hack saw blade to trim for smaller strips. ... I printed these in...
thingiverse
I wanted to install LED strip lights in my camper and I did not want them falling down. The adhesive doesn't always stick. I use mostly the 270mm part and one end piece. I used a small hack saw blade to trim for smaller strips. ... I printed these in...
cults3d
LED light strip holders A very practical way to light up the 3D Printer. Compatible with printers: Ender 3, Alfawise 20/30 and Longer LK4. Compatible with this type of led bar:https://a.aliexpress.com/_dYO7rxG Suportes para tira de luz de LED Uma...
thingiverse
LED light strip holders A very practical way to light up the 3D Printer. Compatible with printers: Ender 3, Alfawise 20/30 and Longer LK4. Compatible with this type of led bar: https://a.aliexpress.com/_dYO7rxG...
thingiverse
Just add led light strip and bolt in on your R/C vehicle and enjoy the night. ...I used 12v ones i got off amazon to use on my 3s powered vehicles.
thingiverse
15cm LED Strip Light The two halves are connected by latches. If it's not strong enough, add some glue around the edges. Print with transparent plastic [obviously]. No supports. ... Layer thickness 0.16 mm or less.
thingiverse
This is my first upload! ... It’s a simple bracket for LED light strips. They can be fastened with double sided tape or screwed in place with small flat head and tapered finish screws. ...