led strip light plastic holder 3d models
651007 3d models found related to led strip light plastic holder.
thingiverse
Low profile LED light strip holder for my Ikea lack table stand Prusa enclosure
cults3d
... is my very first design. ...So please be kind. ;-) I needed holders for a LED strip light that I wanted to mount behind a headboard of a bed. The screw holes are made for 3mm screws. ...The upper holes are meant to fix the strip with a 3mm cable tie.
thingiverse
... my very first design. ...So please be kind. ;-) I needed holders for a LED strip light that I wanted to mount behind a headboard of a bed. The screw holes are made for 3mm screws. The upper holes are meant to fix the strip with a 3mm cable tie. ...
thingiverse
LED Light Strip Holder 10mmx2.5mm Made Screw holes a little bigger for a #6 Also added a "90" for mounting on an edge where you can't get at the bottom The thin walls on either side of the screw hole on the 90 can be fragile, so I printed those at...
thingiverse
Helpful for mounting LED light strips (like these: http://tinyurl.com/o3uwmg3) after the adhesive backing wears off. ... Just nail or tack the mount to the surface and clip in the lights.
thingiverse
expandable led strip holder for printer frame. includes rail for led strip, clips to hold led strip in place if strip does not have sticky backing, bar connectors, rail connector designed to allow tilting towards print bed. also includes a holder for...
pinshape
expandable led strip holder for printer frame. includes rail for led strip, clips to hold led strip in place if strip does not have sticky backing, bar connectors, rail connector designed to allow tilting towards print bed. also includes a holder for...
thingiverse
I designed a mount to hold the LED light strip in my GoKit.https://www.youtube.com/watch?v=Dg9_SA__XPU The Box for my GoKit is a typical 19" Rack mount system used by musicians, etc. So, technically this isn't just a Ham Radio thing. I will put a...
thingiverse
This is kind of a stupid little thingy, but I found it necessary to create in order to hold my LED strip light up against the ceiling of my enclosures so that they wouldn't shine in my eyes. Using LED strip (purchased from Amazon in my case) is a...
thingiverse
simple holder for 2020 extrusion and 10mm rgb strip hot glue or ca glue the strip to print This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/abJf20cQsZE
thingiverse
i have been working on a stair renovation. ...and inserted led. This is for a 10cm led strip. Tip You can also print with glow in the dark. ...nice effect would appreciate it if you print this please let me know,, happy printing
thingiverse
I made this to have an extra light right behind the hot end because the light on my ender 3 v2 still casts shadows and its hard to see where it prints. Use the M3 2020 T nuts to attach it to the frame and you should be good. Im using m3 x 10mm bolts...
thingiverse
I found this LED light strip holder, but needed a smaller version for the lights that I'd purchased. ...This remixed model works with 8mm width LED lighting strips such as the ones found at http://www.amazon.com/gp/product/B00HSF65MC
thingiverse
Holder for an LED light strip IR remote, low profile. Used to hide the remote under my desk. Attached with some some double sided foam 3M tape. ... Can use used with thinner tape.
thingiverse
This is a led light strip remote holder that I designed. ...It works great for this remote...
thingiverse
) https://www.thingiverse.com/thing:2521046 (you need at least one of it ;) ) Using it with a LED-Light for cars similar to https://www.gearbest.com/car-headlights/pp_1577563.html Should also work with normal LED Strips. I attached the LED-Light...
thingiverse
... it did soften and warp a bit in my printer enclosure with PLA so i would suggest using ABS if going inside a heated/enclosed (from the printbed) chamber. ...3 of these strip holders are used in the enclosure picture, 1 above and 1 down either leg.
thingiverse
... the entire thing, as screws were hard to install and wanted a different angle....need to tweak dimensions a bit yet to fit properly on a 2020 extrusion. ... It has some screw on brackets to help hold the led tape on in case the tape doesn't hold it
prusaprinters
A quick clip to hold your LED light strips. These are for the type that come on spools, snug for 8mm wide ones. I made 2, one is smaller designed for double sided tape and the other has counter sunk holes to fit 4mm screws.</p> <p>I made this because...
thingiverse
This is a 10mm LED strip light holder for a Creality Ender 3.
thingiverse
Just simple LED light strip holder for Prusa Mendel Instructions Just print it.
thingiverse
LED light strip holder This is a holder to stick on, of 20cm for led light or whatever you want to add to your 3d printer.
cults3d
LED light strip holders A very practical way to light up the 3D Printer. Compatible with printers: Ender 3, Alfawise 20/30 and Longer LK4. Compatible with this type of led bar:https://a.aliexpress.com/_dYO7rxG Suportes para tira de luz de LED Uma...
thingiverse
LED light strip holders A very practical way to light up the 3D Printer. Compatible with printers: Ender 3, Alfawise 20/30 and Longer LK4. Compatible with this type of led bar: https://a.aliexpress.com/_dYO7rxG...
thingiverse
A holder to place 4 Color LED strip lights into. I use it for the waterproof one and they snap in without adhesive or clips. ... I made this so I could make little strip light panels.
thingiverse
A LED light strip holder for IKEA SOCKER mini greenhouse(701.866.03). The holder come in two parts, a left and a right. If you want to put LED strips on both sides, like I did, you need two of each. I uploaded a couple of different sizes depending...
thingiverse
I designed a LED light strip holder to mount these inexpensive strips https://www.temu.com/goods.html?_bg_fs=1&goods_id=601099513090268 and connect them to the modular vertical hydroponics units https://www.thingiverse.com/thing:3405964 I used...