led strip with diffuser 3d models

The "naked" led strip is too bright to look at it directly, because its luminance. You can add the led strip to my support thing to put it into your computer case. You need to glue the supoprt part and the top part, i used a plastic glue. ... For...

The "naked" led strip is too bright to look at it directly, because its luminance. You can add the led strip to my support thing to put it into your computer case. You need to glue the supoprt part and the top part, i used a plastic glue. ... For...

Print them separately, the diffuser just clips into the housing, no need to glue your light strip in. Just put it in and clip on the diffuser........... It finishes it off nicely and gives off a well balanced diffused light. ...Check the original thing...

Print "led light diffuser v2.stl" in vase mode with transparent (or natural) filament with .3mm layer height, 1mm layer width, one base layer, one outer shell, no top layers, and no infill (like you're making a vase). Here is the recipe: 2x...

I highly recommend piloting holes in legs before securing with screws.Update:Added covers/diffusers to be printed in transparent materials (ideally). ...I printed mine at 100% infill with "clear" PETG and the brightness / go blind balance seems good for...

You can install the LED strip with or without the diffuser. Length is 160mm so you need to print 2 of them to cover the whole length of the 320mm top extrusion. Install using 4 M3 x 6mm bolts and 4 M3 T-nuts. If you use anything longer than...

a strip led rail diffuser. ... the diffuseur v3 stl file is a diffuser with leth sickness so the light can pass with more efficiency.

Diffuser for led strip that is 10mm wide. ...Cut to length.

This is a simple light diffuser for LED strip. Print using clear filament to soften those blindingly bright LED strips. Designed in such a way to connect end-to-end for long lengths. No heat problems with PLA. ... Printed in both 0.4 and 0.8 nozzle...

LED strip diffuser You can find flat diffuser and curve diffuser on the files ,I prefer to use the curve or both at the same time Body 5cm / 10cm / 15cm / 20cm / 25cm Flat diffuser = FD 5cm / 10cm / 15cm / 20cm / 25cm Curved diffuser = CD 5cm / 10cm...

LED strip diffuser You can find flat diffuser and curve diffuser on the files ,I prefer to use the curve or both at the same time Body 5cm / 10cm / 15cm / 20cm / 25cm Flat diffuser = FD 5cm / 10cm / 15cm / 20cm / 25cm Curved diffuser = CD 5cm / 10cm...

Add some diffusion to your led strips with clear PLA. Play around with different infills for desired effects. I chose 60% "Gyroid" infill in Cura. Scale the Z axis to your desired length. Photos show the unmodified 10mm stl and scaled 45mm...

Design intents:Goal was to have diffused lighting for our Voron V2.4Mount directly to 2020 extrusionRe-use off-the-shelf channel and diffuser (leevalley.com , see BOM)Be able to daisy-chain 3 of themWhat you'll find here:STLs3D model (STEP)BOM and...

Works with a 0.4"x0.065" LED Strip. ... Below is the link of the strip I used: https://www.amazon.com/gp/product/B07JP5375R/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&th=1

LED strip holder I created in the process of a future LED strip mount Made it 100mm long but it can be stretched to suit your needs

LED strip holder I created in the process of a future LED strip mount Made it 100mm long but it can be stretched to suit your needs

I needed to angle some LED strip-lights for better illumination of my work surfaces, so I came up with this design. It is fully customisable and is probably best printed with support. I've found that the LED strips don't stick very well to printed...

Led strip mount and diffuser. I made a small and an extended version. Extended version needed to be printed on 45 degree angle for my Wanhao Duplicator i3 Printer. May be the same for you. Use any infill you like, obviously the less you use the more...

Love RGB LED strips for home illumination. Hate the blinding bright spots. Think that commercially available diffusers being more expensive than the light itself is ridiculous!!!! This might be a solution for you. I have designed it as...

I needed to angle some LED strip-lights for better illumination of my work surfaces, so I came up with this design. ...It is fully customisable and is probably best printed with support. I've found that the LED strips don't stick very well to printed...

diffuse you LEDs! Be sure to read the manual to see how. STLs for reference only. Use openSCAD/Customizer to customize to your setup. need a box? ...https://www.thingiverse.com/thing:5754914 please only post remixes that are not from...

Customized version of https://www.thingiverse.com/thing:1634567 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1634567

Add some diffusion to your led strips with clear PLA. Print a "dome" and a "clip" then sandwich the LED on your strip. ... Fusion 360 file Included!

Led Strip Light Diffuser, 50mm length Brims recommended.

Parameters (in milimeters) : * `length` - length of LED strip you want to cover (in my case, 50mm per segment) * `width` - width of the LED strip (usually around 10mm) * `height` - height of the LED strip, with diodes (in my case - 2mm) *...

This is a quick and simple light diffuser for the common IKEA "Ledberg" LED strips. When printed using translucent filament, it turns the LED strips into coloured mood lights! Instructions This needs...

It is for LED strips up to 10mm width. If you need another length just add a modifier as a negative volume in prusa slicer and cut the length as needed.There are two versions. ...One is flat, the other is with a 45° angle which I used for the sides...

Diffusers of varying length used to smooth the light coming from my under-cabinet LED lighting strips. With these attached, the light now appears to be a continuous line rather than individual bulbs. Apologies for the random lengths; this is what I...

This diffuser is designed specifically for the 4pin WOWLed magnetic 30cm RGB light strips that you can get from amazon they come in a three pack with a three way adaptor. If you print these with a translucent white filament they diffuse really...

This is a remix of the [LED Strip mounting profile](https://www.thingiverse.com/thing:2533803) by [HansVaa](https://www.thingiverse.com/HansVaa). The original top part has a thickness of approximately 1 mm. I changed this to 0.4 mm as it looks a...