ledstrip 3d models

Simple LEDstrip that you can set your own number of LED's

To add a ledstrip to the Snapmaker 2.0 printhead I made this holder.

Needed a ledstrip mount, found some on internet. They where all a bit meh.<br/> So made my own.<br/> They work pretty good, you can even clip cables under them.<br/> I was not sure about the orientation of the print, made some sidewalls to hold the...

Simple fastener for 3x10mm ledstrip. ...uses 2,8mm screws

Holds a small ledstrip and strongly fits on v-slot profile. ... FreeCad file so can be edited

ledstrip soldering help for 3 pin leds, i mad it for my digital leds. ... its for led strips with a width of 12mm.

This box can control an RGB ledstrip up to 5m using WiFi on the RGB WiFi app for Sailfish OS. ... Demo: https://www.youtube.com/watch?v=CUqqFN2gjLo App: https://www.github.com/DylanVanAssche/harbour-rgbwifi Code:...

ledstrip soldering help for 3 pin leds, i mad it for my digital leds. its for led strips with a width of 12mm. Category: Electronics

For my boat innerroof, i plan to fit in ledstips between the roof tiles and the same time hold the tiles upp. ...Easy access to the innerroof remove led strip and unscrew. Screws hidden beeneth the ledstrip. ... HAVE NOT PRINTED OR TESTED IT YET!!

For my boat innerroof, i plan to fit in ledstips between the roof tiles and the same time hold the tiles upp. ...Easy access to the innerroof remove led strip and unscrew. Screws hidden beeneth the ledstrip. ... HAVE NOT PRINTED OR TESTED IT YET!!

Angle holder for ledstrip. Angle is 55° and it holds about 10,1mm wide strips. I have used it for yeelight strip and it snaps beautifully in place. You can fix it with 2 screws or double sided tape. ...Screw size is 3X12.

... from this thing https://www.thingiverse.com/thing:2194847 on the lamp part. ...Now it fit to a ledstrip 10mm with 3mm height. The little block is from the original remix. It fits very exactly for me. ...Pictures of fitting will be upload later.

... they are all a bit meh. ... So made my own. They worked pretty good and are pretty flexible but still very tight, you can even clip a cable under it without problems. By not using 2 screws you can always replace a ledstrip without unscrewing stuff.

This is for a project that I'm working on, it hold a ledstrip for an example ws2812b 5050 leds perfect without any glue or so. You can probably with outer leds if you want to but i needed addressable leds for my project. I'm using this on a board...

<p>this is an holder to hold a ladstrip in a IKEA Lack enclosure.</p>

this is a clip to hold a 45 degrees profile for ledstrips. ...Print Settings Rafts: Doesn't Matter Supports: No ...

Ledbar for 5050 ledstrip with cover 150mm

A mounting hook for the ledstrip from IKEA DIODER ledstrip http://www.ikea.com/gb/en/catalog/products/00119419/

This frame ledstrip don't need screw, glue, ... ... Just fix the support in the printer and the ledstrip in the support. ... And it's functionnal ;-)

Derived from the Orca 0.43 Ledstrip, this one is for the Luna 0.20 which has 15 mm tubing. Each part is 100 mm. ... Instructions Each part is 100 mm

I Designed a bracket to support a ledstrip profile I had laying around. I made it so that it hooks in the upper profile. There is a cutout so a switch can be fitted in the support You can put the cable in the aluminium profile. My led strip is...

I needed a replacement light in my arcade cabinet, a LED strip of 12Volts can get his power directly from the Arcade power supply and it's cheap. ...I used this simple mount to attach the strip.

print and have fun

Customized version of http://www.thingiverse.com/thing:594201 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=594201 Instructions Using the following options:...

Ceiling mount for LED strips with silicone encasing, similiar to this: https://www.amazon.de/Lamomo-Wasserdicht-Lichtleiste-Controller-Aussenbereich/dp/B08SLWPCFB/ref=sr_1_9?c=ts&keywords=LED+Streifen&qid=1677879887&s=lighting&sr=1-9&ts_id=3884370031...

I took the clip from thing:4636337 and the ledstip holder from thing:225216 and combined them to create this 18cm led strip clip-on for a 2020 frame I made this using TinkerCad, and adjusted it so that it can be printed upright without supports. ... ...

Led mounting bracket for the prusa mk3 series Led strips rigid 12v 5730 led strips pair of 3 breakaway strip

Customized version of http://www.thingiverse.com/thing:594201 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=594201 Instructions Using the following options:...

I did this with what I had at home This is the first version diy led strip holder for M365 pro2 need: HARDWARE: bl-5j battery Wire,solder..... ... led strip (5m-60-ip67) : ...

Customized version of http://www.thingiverse.com/thing:594201 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=594201 Instructions Using the following options:...