lee load all 12 gauge

Tired of the Lee Load-All's red cap that's full of parts, rattles, and too easy to knock off, scattering all your inserts, and basic tools? Just yeet it into a corner, with this upgrade. Its got modular inserts, with options for either 30 primers, a...

Adaptor to allow the Lee Load All 2 Shotgun Press to be used with the Lee Quick Bench Mount. I split this as the size of an adaptor would not fit on the base of my ended. Printed both parts at the same time, oriented as pictured. ... Print with 75%...

But it looks all workable. What is needed besides the printed parts: - 8 * M3x20 screws - 2 * M3x16 screws - 10 * M3 nuts - 8 * M3 washes - 4 * d6 h10 magnets - 4 * d6 h4 magents - 1 * tek-lok clip with screws and nuts (usually included) ...

... printing bushings. ...These bushing uses with Lee Load All presses P/N: 90011 90015 90012 and same. Volume: 1.9 gram, 2.0 gram, 2.1 gram, 2.2 gram, 2.3 gram Please chech your scale before printing. All draws with mesures located in zip-archive. ...

Upgrades to obtain a better final crimp of AA HS Hulls. See readme file. ... https://www.youtube.com/watch?v=8H-yO1Z3z5E

Holders for 3 Lee Load-Master Turrets. ...Designed to be screwed to the side of a reloading bench.

This is a box designed to hold two Lee Load Master turrets for storage. The box will allow you to store the turret with your dies preset so that you can avoid having to reset everything when changing out calibers on your press. The box is stackable...

... Super Glue). I had to print the cover at 1.004 scale for X and Y since my transparent PLA seemed to shrink a little. The latches are setup so that all levers latch towards the funnel / press so gravity will help keep them in place when on the press.

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Font_name = Chewy Loop_font = Chewy Loop_character = o Loop_y_position = 0 twist = -3 Loop_x_position = 11 Rotation = 50 center = 60 spacing =...

This is a case for a Lee Load Master 5 hole turret with Dies. The Base has holes to support the turret with Dies in place. It is threaded with large threads, that shouldn't need supports to print. ...The cap - which comes with .223 and blank - holds the...

This is a Lee Load-All II Bench Plate Mounting Block. Print out both parts and bolt them together along with the press. Gluing the pieces together using superglue or epoxy would be a good idea. Sorry, the Cusomizer doesn't like my code for some...

Scales for weighing gunpowder and lead to recharge caliber cartridges 12

12 gauge cartridge (12/70)

lee by Jay [created on 3DTin]

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: twist = -3 spacing = [10,11,11,13,14,14,14,15,15] Rotation = 50 height = [5,6,4,5,4,3,5,4,6] Loop_character = o Loop_font = Chewy Loop_x_position...

Ruff 12 gauge

This will hold 16 12-gauge 2-3/4" or 3" shells securely in four quads. You can also TWiNS load (two at a time) off of this carrier without too much difficulty. I've run this design in many competitions and never had a failure or a dropped shell...

2.25 inch 12 gauge dummy shotgun shell for training. I made this because the other versions of dummy slugs on thingiverse did not have the correct dimentions I needed a few dummy shells to test out the pump action on my maverick 88 because I...

Customized version of http://www.thingiverse.com/thing:154662 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=154662 Instructions Using the following options: canh = 122 bold = Yes text = Lee

Customized version of http://www.thingiverse.com/thing:154662 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=154662 Instructions Using the following options: text = Lee canh = 122 bold = Yes

This is an ammo belt holder for 12 gauge shotgun shells. Designed for a work colleague who regularly takes place in feral pig shooting. My design goals for this were to minimize filament usage and print time (each clip is about 9g and takes about...

12 gauge live ammo in a single print.

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_thickness = 4 Font = write/orbitron.dxf message = LEE flat_bottom = 1 hole_radius = 1.5 stick_thickness = 3 font_size = 10 stick_width = 8

http://www.thingiverse.com/apps/customizer/run?thing_id=56879 Instructions Using the following options: top_hook_diameter = 15 letter_depth = 2 bottom_hook_thickness = 3 hook_depth = 1 border_depth = 1 border_fullness = 20 reminder_text = Lee...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 3 message = Lee hole_radius = 3 font_size = 15 font_thickness = 5 stick_width = 8 Font = write/orbitron.dxf flat_bottom = 2

http://www.thingiverse.com/apps/customizer/run?thing_id=408698 Instructions Using the following options: text = lee pencil_color = green pencil_width = 10 pencil_hole = 1 text_thickness = 3.5 show_pencil = 1 letterspaces = [55,55,55] pencil_sides =...

http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: wall = 1 do_shift_font = automatic textstring = Lee textsize = 25 textheight = 10 shift_font_percent = 0.07 base_radius_add_percent = .1 fontname...

12 gauge shotgun shell 1:1. ...Feel free to use it and hit the like button!

Compensator for 12 gauge shotguns.IPSC open.Work well on any cartridges.

A simple (heh, 14 iterations later...) 12 gauge snap loader that I designed to fit my Turkish made Khan Arms brand Arthemis model over-under shotgun. The barrels are 25 mm apart so it should work on any similarly spaced SxS or O/U break-action. I...