lego breaking bad rv 3d models

A customized version of the model available at http://www.thingiverse.com/thing:134297 was created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=134297). ...The specifications used for this customization include a...

My motorhome came with a central vacuum system, but using it with the extra-long bulky hose was like wrestling an anaconda. I much prefer a broom and dustpan. And, so, because I could, I designed two dustpan versions to connect to the central vacuum...

Motorhome rear ladder has end caps that are deteriorated after sitting outside for many years. This fits Kemberly Atwood ladders. Use PETG filament for better life outdoors. ...

A tailor-made hinge specifically designed for a motor home can be obtained through special order. ...This ensures proper fit and functionality, catering to the unique requirements of a motor home.

In 2019, I bought a Power TechON 2000W Pure Sine Wave Power Inverter with remote for my motorhome. By the way, this inverter is now called GoWISE. After some searching, I finally settled on a spot to mount the remote. The most convenient location was...

I purchased a 2005 motor home and have been slowly fixing some of it's many problems. One was several drawer latches were broken and the latches I could get were not the same size and would require new holes. Since I did not want extra holes I made...

I installed a slightly larger water pump in our motorhome, necessitating extra space between the new pump and the Surflo water inlet regulator. To accommodate this, I added a spacer that fits snugly between the stainless steel fascia of the wet bay...

Standard Trailer Light Lens.

The individual in question possesses a lack of personal details.

A quick MMIII deployment wafer bowl that I designed. It is a simple print - use whatever settings you normally use. I did find that I had to slow my print speed toward the top of the RVs (I made the adjustment at layer 550), to keep the layers...

These things often fail on RVs. After ours repeatedly malfunctioned, I chose to disassemble it. Consider keeping a few extras in your camper. If you found this helpful, a tip to my paypal.me would be appreciated. Thanks and have fun camping!

This is a motorhome trailer birdhouse, with an entrance diameter of 2 3/8 inches. The vehicle frame and wheels are firmly attached together using super glue and PLA as the print material. For mounting the roof rack, use M4x 12mm screws; I've added...

Staircon export by Stolmark Marek Kesy, license number 6599.

One of my camper downspouts was draining directly onto the tip-out awning and causing it to fill with water and sag. ...This spout takes the water further along the trailer and dumps it off the side.

Ön kısım daha küçük yazıcılar için 4 parçaya bölündü

Polycam.ai Crafted a Human Form

Does your RV fridge not latch? ...does it swing open? On my RV I noticed the door was sagging and this was my quick fix. I printed two and snipped a wedge into them so I could slide them into the hinge without taking off the door. ...Perfect fix!

... a 8.5mm square rod with a removable handle. ... This handle may be left on the RV permanently and doesn't require and tools or modifications to the existing valve rod. ... I printed it with 5 walls and 50% infill, to make it as strong as possible.

This is another version of my RV inlet mount that combines both the 30 and 15-amp mounts. The 15-amp hole will also accommodate a 20-amp inlet. ... I installed a 20-amp circuit so that I could pull a total of 50 amps into the RV when needed.

Searched all over the internet, not a single file for the RV sewer pipe connector (bayonet fitting 3" hose). So I created it. This is to adapt a craftsman gas blower exhaust hose to a 3" RV sewer hose, or running a dry washer (gold...

... Table Lamp boasts a width and depth of 22cm each, with a height of 53cm. ...On the other hand, the RV Astley Thomas Griem Hurricane Floor Lamp features a metal construction and measures 30cm in both width and depth, towering at 164cm in height.

This si a simple 1.5 NPT to Thetford bayonet adaptor that will allow you to flush the blackwater RV line, then connect the hose to the graywater adaptor to flush the RV sewer hose. This model should be printed in ABS with supports for the...

This is a Lego shelf. ... If you like my design post a make/like or comment and I will make more.

This spacer is designed specifically for attaching the Otto B8 stick grip to the front seat control stick of an RV-8 aircraft. ...It ensures a proper and secure installation, enhancing the overall flight experience.

4" RV Camper Trailer Bumper Cap Cover by Koganinja was just a touch too large for my bumper, so I remixed it to fit. My bumper is 96mm inside dimensions, 101.5mm outside dimensions. ... Worked perfect!

Download a crisp, detailed RV-7 printable model, complete with optional features that allow you to pick from either a Nose Cone with the Propeller in place, or remove it entirely based on your preferred configuration.

Stall Vane safety cap to prevent the sharp metal of the stall vane actuator from injuring a person. ...A "Remove Before Flight" can be added to provide additional visibility when installed. Designed specifically for Van's Aircraft RV-12.

In this particular case, my winnebago Travato RV, has the main battery power off switch very close to the floor near the entrance to the RV. We have accidentally switched off the power with our feet many times. This switch protector will prevent...

I'm installing an anode plug on a 6-gallon Suburban RV water heater, allowing me to store the RV while preventing corrosion of the water tank. This plug will keep water inside while I perform maintenance, soaking the tank with vinegar to remove scale...