lego case for raspberry pi 3d models

This is a prototype of a Raspberry Pi case that I've been developing. It's compatible with most models, including the 2 B+ and 3 B+. As you can see from one of the photos, a model 2 B+ fits snugly inside. The Pi board goes together seamlessly. These...

After crafting the "LEGO attachable Raspberry Pi Zero W case" (thing: 2732553), I realized that an interface plate for projects not built with LEGOs would significantly expand the usefulness of the case. The LEGO interface makes the Rpi Zero W case...

For incorporating your Raspberry Pi Zero into a prototype device, the Pi Zero W also fits perfectly. It offers unrestricted access to the GPIO pins while safeguarding against physical impact. The enclosure remains open for the camera cable. Some...

A Customizable LEGO-Compatible Case for Raspberry Pi 3. The case is designed around a 12 x 8 grid, equivalent to 12 classic LEGO bricks. Find tutorials and electronic component lists on our Product Page at...

Download: https://learn.adafruit.com/raspberry-pi-pico-case Our LEGO compatible mount features studs that fit standard bricks or base plates. It features built in standoffs so you can snap fit the Raspbbery Pi Pico right on top. Our 3D printed...

Download: https://learn.adafruit.com/raspberry-pi-pico-case Our LEGO compatible mount features studs that fit standard bricks or base plates. It features built in standoffs so you can snap fit the Raspbbery Pi Pico right on top. Our 3D printed...

And it's Lego, so stackable for free! Holds a Raspberry Pi 4. ... BOM with https://www.bricklink.com part numbers Brick 1x2, 5, 3004 Brick 1x3, 1, 3622 Brick 1x4, 2, 3010 Brick 1x10, 1, 6111 Brick 2x2 Corner, 1, 2357 Plate 1x2, 2, 3023 Plate 1x3, 1,...

It is meant to work with the LEGO case for the Raspberry Pi Zero I published at https://www.thingiverse.com/thing:4669644, although it is also suited for the bigger cable of the other Pi variants. ... Printing recommendations Camera mount • Infill 40%...

Transparent case for Raspberry Pi

When searching for a Raspberry Pi W Zero case that can be attached to LEGO bricks and plates, I find none that quite meet my needs. I decide to merge two good existing models. Using geertvda's Raspberry Pi W Zero case which is one of my favorite...

This a case for Raspberry Pi Zero case to be combined with LEGO bricks A mount for the Night Vision camera for this design is available at https://www.thingiverse.com/thing:4653398 Print the box with the stud’s side down and the cover with the stud’s...

This is my latest creation - a one-of-a-kind LEGO Compatible Raspberry Pi case designed specifically for the Raspberry Pi B+ and 2. It's perfectly crafted to blend in seamlessly with your existing LEGO creations, using standard stud and block...

To attach a Raspberry Pi to my robot, I designed a LEGO-compatible mount suitable for BrickPi and PiStorms devices. ...Securing it in place are two pins or axles that lock it shut.

This Raspberry Pi case (http://www.thingiverse.com/thing:92208) is the original design, while the attached Technic part (http://www.thingiverse.com/thing:13518) has its mounting removed for a custom fit. ... Here's an alternative version: The base model...

Case for Raspberry Pi 3 (suitable for 3.5" touchscreen/display on an RPi3)

... for purchase. ...Raspberry Pi, a trademark of the Raspberry Pi Foundation, can be found at http://raspberrypi.org/. This case helps protect your Raspberry Pi and provides easy access to its components, making it perfect for breadboard projects.

Case for Raspberry pi 4 card. No screws are required to assemble the housing or Raspberry, only used for the fan. ... No cable outlet.

The case is also compatible with Adafruit's low-profile microSD card adapter for Raspberry Pi, requiring removal of the support peg for standard SD cards. For 3D printing enthusiasts without a printer, BadBrick offers printing services via...

This base plate is compatible with Adafruit's Low-profile microSD card adapter for Raspberry Pi, requiring only the removal of a support peg for standard SD cards. As shown in the image above, this setup provides a neater solution than having a...

This is a Raspberry pi case for Mk3. ...It is designer to attach to the aluminum profile of your printer.&nbsp;</p>

NZXT Case for Raspberry Pi. Will fit more other Pi's but check. Top is glued on. Rings are pressed in, very tight. Perhaps print them 99% in all dimensions. Bar is also pretty tight. ... Snaps in.

... this project for ages. ...It's a great opportunity to build a custom case for my Raspberry Pi, hard drive, and cooler. ...To get it powered up, I'd recommend using a sturdy 90-degree USB connector to connect the Raspberry Pi to a reliable power source.

To view the complete write-up of this case, check out our blog post: https://www.219design.com/cool-your-raspberry-pi-3d-printed-case/ Here’s where you can buy a compatible fan: https://www.adafruit.com/product/3368 Our case is designed for two...

For a detailed overview of our design, visit our blog post at https://www.219design.com/cool-your-raspberry-pi-3d-printed-case/. If you're looking for a compatible fan, you can find one at https://www.adafruit.com/product/3368. Our case is designed...

Custom Enclosure Kit for Raspberry Pi 4 Designed to Fit a 40mm x 10mm Cooling Fan

The case is engineered to accommodate various types of hardware, including Raspberry Pi, ODroid, and similar devices. Ample space is provided within the case to incorporate a speaker, microphone, and batteries. The larger case was printed at 100%...

Base for Raspberry Pi case. Tip: When printing with Repetier on my FDM printer, the part shrinks horizontally by 2%. ... To counteract this effect, I adjust the scale of the piece: Z: 1.02 Y: 1.00 X: 1.02 In DLP printers dimensions are precise

The main part of the case slides over the Raspberry Pi, and a cap fits around the connectors. The parts are only held in place by friction so it probably isn't a good option for transport or if you frequently plug / unplug devices (mine just sits...

This version also features tighter tolerances and tweaks to the design that make it simpler to print, as well as an added latch on the cap so that the Raspberry Pi stays in place when you close up the case. This design is intended as a simple sleeve...

Measuring a genuine raspberry, this is my initial project on the website. ...To produce it, purchasing certain components is necessary. Both printable parts can be found in the STL folder. I utilized Alexandre Willame's Raspberry Pi for this task.