lens hood for canon 18 135mm stm 3d models

... Should be compatible with: EF-S 18-135mm f/3.5-5.6 IS / IS STM EF-S 17-85mm f/4-5.6 IS USM EOS Rebel T4i 18-135mm IS STM EOS Rebel T5i 18-135mm IS STM EOS Rebel T5i EF-S 18-135mm f/3.5-5.6 IS STM EOS 60D EF-S 18-135mm IS EOS 7D EF-S 18-135mm IS

Should be compatible with: * EF-S 18-135mm f/3.5-5.6 IS / IS STM * EF-S 17-85mm f/4-5.6 IS USM * EOS Rebel T4i 18-135mm IS STM * EOS Rebel T5i 18-135mm IS STM * EOS Rebel T5i EF-S 18-135mm f/3.5-5.6 IS STM * EOS 60D EF-S 18-135mm IS * EOS 7D EF-S...

Having a Canon EF-S 18-135 STM lens that come without a hood, I try to print both Canon 18-135 STM lens hood and Canon EF-S 18-135 Lens Hoods. Both can't be reverted for storage. Furthermore the second one is too heavy but the full version despite...

Print Settings Printer: OverLord Pro Rafts: Doesn't Matter Supports: No Resolution: 0.1mm Notes: The print settings is the very same as for Canon 18-135 STM lens hood. ...For the first print, I suggest you print only the base and them adjust the scale.

I've adjusted the model to fit my lens: Canon 18-135 STM (T4i kit). The original hood is the EW-73B. Instructions Print and use. ...It should be possible to mount the lens hood "inversed", when not in...

This has been specifically designed to work with the new stm version of the lens and will not work with the older non-stm 18-55 3.5-5.6~ Surprisingly, i could not find a lens hood that would work with the new stm version of canon's 18-55 kit lens. ...

This is a lens hood to fit the bayonet connector on a canon 28-138 mm lens.

quack basic dirty adaptation for bob345 to protect from rain

This is a lens hood for Canon 50mm F1.8 EF STM. ... It can be screwed to the lens the other way around.

Lens hood for Canon EF 50mm f/1.8 STM, screws right on the mount. ... Only tested on crop sensor, might be in frame on full frame cameras.

Print SettingsPrinter: Flashforge Creator ProRafts: NoSupports: YesResolution: 0.20Infill: 20%Notes: Support resolution has to be reduced to make sure the lens hood mount rings print accurately. ...I used 123Design and Simplify3D to print this.How I...

... Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 Infill: 20% Notes: Support resolution has to be reduced to make sure the lens hood mount rings print accurately. I used 123Design and Simplify3D to print this.

It's my first real design from scratch, so don't hate on it, but it does fit very well on my lens, clicks into place with the original lens hood mount. I have included a thick version and a thinner version. Print Settings Printer: Flashforge Creator...

I printed out the lens hood by VHMaple and it kinda crumbled in my hand. It could be entirely my printer and settings, but I edited it to make it a little thicker anyway. When I printed mine, I ended up having to scale the hood to 99% to get it to...

This is a remix of https://www.thingiverse.com/thing:443442 It is designed to fit the NEW CANON 18-55 IS STM since these have a different hood mount (2 contact strips instead of 3)

This is a remix of Manticorp's hood for the Canon 50mm f/1.8 STM lens. I used the original as the basis and redrew it in FreeCAD. *** Note that it is design for the new STM version. *** Having acquiring the lens, I don't want to pay the ridiculous...

Remixed to remove the logo, updated the lens hood mount to fit my Canon 55-250mm IS STM as it only has 2 flanges rather than the 3 on the original STL. Fits great on my lens, but your mileage may vary. Print in black for best results, or paint the...

It's a camera hood designed for a Pentax DA 18-135mm lens. Works well, very happy with it! Does make quite a snug fit. ... Updated to allow it to be stowed in the other direction, added light trap on the internal section, and with a new pattern on the...

Yet another remix of laurent_despeyroux's deep lenshood, this one for the Canon 18-55 lens. I used the bayonet mount from larsrc's Canon hoods. THIS HAS NOT BEEN PRINTED OR TESTED - I don't have this lens. I'm counting on someone to try it out and...

This version has thicker walls, the Canon logo, and locks onto the lens. ...No supports required. (for STM lens not IS II)

Using http://www.thingiverse.com/thing:587750 and http://www.thingiverse.com/thing:94534 i have create this one to use with 24mm STM lens. ...Looks good and do the job Print Settings Printer: MakerFarm i3V ...

Un pare soleil pour objectif Canon. ...(Le 18-55 par exemple)

This is the hood I designed for my EF-S 18-55 f4-5.6 IS STM lens which is the latest version of canon 18-55 lens series. I don't know if it will work with the EF-S 18-55 f3.5-5.6 IS STM version, but the hood canon listed for both lenses are the same...

Using http://www.thingiverse.com/thing:587750 and http://www.thingiverse.com/thing:94534 i have create this one to use with 24mm STM lens. Looks good and do the job Print Settings Printer: MakerFarm i3V Rafts: Doesn't Matter Supports: No Resolution:...

Lens hood for Canon lens EFS 18-55mm.

Lens Case for 18-135mm by Canon. 

A cylindrical lens hood i made for my Canon EOS 2000D. A lot of the designs on thingiverse are petal hoods, which don't work with this model as the petals move when focusing. I am a novice photographer, so if anyone has more experience please feel...

A lens hood for Canon EF 50mm f1.8 STM lenses. ... Can be used both as as hood and as a protective case.

A small change to the original one for fit lens 18-55 that was included with my 650D. Removed part of the bottom pins that were 4-5 mm thick, now 1 mm and fit perfect on the lens. ... Instructions...

This is a lens hood for canon STM 50mm . Perfect fit (if printed right) , clicks in place . Fit tolerance is printer dependent , adjust setting if too tight or too loose . ...