leviton wall plates 3d models

If you need a wider plate with fewer holes, this piece will snap into the unused holes.

... did not have enough clearance for Leviton's thicker retaining bars which caused the blanking plate to not sit flush with the front of the wall plate.  I redesigned the blanking plate from scratch using measurements from the Leviton wall plate.

Replaces Leviton 27 Wall Plate (US plugs, electrical). This has a smaller neck (distance between plugs) of 9.334 mm than other wall plates in order to fit perfectly. Pictured plug is using a blue-based glow-in-the-dark filament. In the future, I'll...

Replaces Leviton 27 Wall Plate (US plugs, electrical). This has a smaller neck (distance between plugs) of 9.334 mm than other wall plates in order to fit perfectly. Pictured plug is using a blue-based glow-in-the-dark filament. In the future, I'll...

Just something I whipped up in fusion 360 for a specific application. ...IDK if anyone will ever need this but I posted it just in case

Similar dimensions as the off-the-shelf wall plate: https://www.homedepot.com/p/Leviton-Decora-1-Gang-Wall-Plate-White-R52-80401-00W/100036991 This is designed to be a multi-material print. I printed this using a Mosaic Palette 2 and was sliced in...

Decora / Leviton Electrical Wall Plate Blank Insert. This blank Decora wall plate is dug-out on the back so that the face is only 3mm thick. It is suitable for low voltage signal and data connectors such as ethernet, HDMI video, and audio. ...

We use Leviton Tamper-Resistant toggle switches for hallway lighting, and I was annoyed at how their metal key has a hole in the middle. This makes it difficult to sit in a key ring with all other keys hanging flat (not to mention increases the...

In addition to the printed part, you will need some appropriate screws (I have found that sheet metal #6 at 1/2" in length are fine) for the wall mount nubs, and Leviton's push-lock fasteners. The STL included has appropriate spacing for putting...

Leviton 12 port Patch Panel Wall Mount for punch down block. I had a panel, but no way to mount it. Included the FreeCAD for easy future changes, for instance could use the middle brace that is common on these blocks. ... It works well!

wally plates

I wanted to make a glow-in-the-dark light switch, so I measured it all out to replace an existing switch plate. ...This is for a Leviton type switch (the wide and shallow type)

Cover plates for Decora-style wall switches and outlets.

Cover plates for Decora-style wall switches and outlets.

I initially considered using WALLY - Wall Plate Customizer, but I wanted the screwless look, so I made these designs.On my personal prints, I also added some engraved text to describe each switch on my personal wall plates. The lettering is not...

I needed some Keystone wall plates with different keystone configurations. These have gotten really expensive at the store, so I went looking on thingiverse. There are others out there, but the ones I've found and tried were not the correct size...

I got tired of the RJ45 cables sticking out from the walls and opted to design a recessed version so that one can push furniture up to the wall without damaging the RJ45 plate. I am posting the single and dual versions of the design. I actually have...

There are 3 sizes of wall plates: Standard (2.75 by 4.5 inches) Preferred (3.13 by 4.88 inches) Oversized or Jumbo (3.5 by 5.25 inches) Standard is the smallest size and is normally used in newer homes where tolerances are tighter. Preferred is a...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 5th_plate_bottom_hole = stereo 3rd_plate = hdmi 1st_plate = outlet 2nd_plate_bottom_hole = hdmi plate_width = 2 4th_plate = usb-b...

All of these models were made from measurements of existing Leviton faces, except for the blanks. All of these models have been printed, test fitted, and installed throughout my house, except for the 2-gang and 3-gang blanks. As I have no 2 or 3...

Couldn't find a 3D modeled set of Decora wall plates anywhere online, so I made some based on widely available dimensions. This print is a direct replacement for any Decora rocker, Decora outlet, or GFCI outlet cover (see dimensions pic). Great...

LEVITON ELECTRICAL PLUG PART # 26W81

Cable Pass-Through Wall Plates Original design by Sdsyc

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 2nd_plate = none plate_size = 0 3rd_plate = none 5th_plate_bottom_hole = none 1st_plate_bottom_hole = none 3rd_plate_bottom_hole = none...

... or outlet coverage. Though you could use it under a standard plate to get the extra coverage if there was damage to the wall around the box and need to cover more... Print instructionsUnassociated tags: cover plate, wall cover Category: Household

Snap in wall mount plates for Lifesmart Cololight Can be mounted with screws but it works great with mounting pads that leaves no holes in the wall. Print in accent color for a nice background effect of your white cololight units from the wall.

The plates provide enough surface for the double-sided tape to stick to your wall properly, and can be fixed to the exitisting screw holes in the wall mount with M3x10 bolts (DIN 912, for a flush look). Print two locks and each plate, no supports...

Simple wall cover plates for the starlink cable cord. This has two versions. One is a two-screw, three-piece part that fits standard wall boxes. ...The second version has three screws and two parts, and is better suited for box-less applications.

... a slip over and trap in place, not a screw in/on, so not for standard wall switch or outlet coverage. Though you could use it under a standard plate to get the extra coverage if there was damage to the wall around the box and need to cover more...

... a slip over and trap in place, not a screw in/on, so not for standard wall switch or outlet coverage. Though you could use it under a standard plate to get the extra coverage if there was damage to the wall around the box and need to cover more...