lid for soda can 3d models

Print this in PLA or other non-toxic material No support required It can fit for all can for me, middle sized soda "33", big can like "monster" "50", little can "25" etc... ... Edit: Can Lid v1.2 updated with a better design and solidity tap

A handy way to store multiple drink tops for cans. Ideal to save left over drink in cans. Handy four set. Can print in any material desired.No support nor brim needed. ...Basic, easy, and useful print.</p>

Customized version of https://www.thingiverse.com/thing:5555214 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5555214

Lid for Soda Can. Print instructionsLokk should be printed in PLA Ring can be printed with Flexible fillament.

Lid for soda can, Designed to be printed with flexible filament; I used flexible TPU filament to print these and they work great with a good seal, no supports are needed in either designs. canLid.stl was my first version and it works great and...

Update 2 July 2019: Check out my vase/spiral printed cans https://www.thingiverse.com/thing:3726621 ------------------------- A snap on lid for a soda can. Soda can lids are standardized. This lid works on 7.5 oz., 12 oz., and larger cans in the...

Snap on lid for a soda can. Snaps on securely, but not quite airtight. Instructions This is about my 4th revision of this lid, all drawn in Google Sketchup (file attached). It snaps on very securely to many brands of soda cans, but is not quite...

Snap on lid for a soda can. It snaps on very securely to many brands of soda cans, but is not perfectly airtight. This is designed so you snap on the front two clips first, then the clip with the lever. ... If you like this design, consider rating or...

... more comfortable than a can. ...So why not turn your can into a bottle. Take your energy booster with you without thinking about spilling in your backpack. This lid uses a rubberband as a seal and any standard PET bottle cap. ... *please note: WIP*

A lid for a soda can to stop flies getting in etc. It keeps the fiz in drink a bit longer. ...Keeps you from spilling it

I printed several of the Soda Can Lids and loved them. ... I created a holder that holds up to 8 of the soda can lids to keep them organized. Fits @tmorris9 Soda Can Lid perfectly. ...

TPU soda can lid. Slows down your opened soda from going flat if you want to save it for later. Also keeps bees and wasps out of your soda. Customized version of https://www.thingiverse.com/thing:5555214 Created with Customizer!

... in the throat, like INSIDE the throat, due to the wasp was in your soda can while you drank from it? ... Fear no more - the life saver is here! The Soda can lid (for the new 33 cl cans) Print in PETG for that extra "snappiness". ... Chill out!

Hey, I have made this soda can lid for protection of bees wasps and other bugs it has been tested and work fantastic on all soda/beer cans. ... hope you like it and will follow me for future awesome things (: -NBD

ITS A 54MM SODA CAN LID TO KEEP THE GAS INSIDE IF YOU CANT FINISH IT IN ONE GO.

The Soda can lid by tmorris9 but printed at 95.5% so it fits the new 250ml and new 330 (stretched) Coca Cola cans. ... It has a nice tight fit so your soda pop keeps fizzy :)

the solution is a lid that clicks on a soda can with a rotating top lid so you can open it when you want to drink, and close it when you are not, keeping wasps and the like out of it. I added serated edge for better grip when opening with index...

the solution is a lid that clicks on a soda can with a rotating top lid so you can open it when you want to drink, and close it when you are not, keeping wasps and the like out of it. UPDATE: added serated edge for better grip when opening with index...

Hello, I designed a soda can lid in the past, but came across Coeproto's "Fizz Saver" thing and liked that design much better. I decided to take theirs and tweak it slightly. The main thing I did was add a tab to help pull the lid off which helps...

a lid for a coke can free for you

The lid you've always needed. ...Clean and spill free and also prevent the risk of swallowing insects such as wasps and bees. Make sure not to tweak or scale, otherwise the DIM will not fit the standard size of soda cans.

I tried making an air tight lid to save sodas for later. This is as close as I could get. It fits very tightly depending on the brand. On some cans I could fill with water and turn them upside down with no leaks but if I squeezed the can it would...

Hello, I designed a soda can lid in the past, but came across Coeproto's "Fizz Saver" thing and liked that design much better. I decided to take their's and tweak it slightly. The main thing I did was add a tab to help pull the lid off which helps...

I needed a lid for my 250mL cans. It has a lip on the inside to hold on firmly to the can, it doesn't come off easily! ... No supports needed, print with the top laying down.

This a lid and cap that you can pop onto your canned beverage.

Push the lid down from the top while holding the bottom of the can to put it on. Use your thumbs under the lip of the lid to pop it off. May need to be trimmed or filed a bit to get the best fit. Scale by 25.4 for proper size. ... The one with the...

The lid is sized for a coke can. Fits pretty well and has a nice lip that creates a snap fit. ... Instructions Printed at 0.20 layer height with diaphragms and 60% infill.

I designed this dor my friend (Pelle). ...He always wants to drink a soda between the lessons, but the time that he has is only 10 minutes. So with this he can close his can and keep it in his bag without all his books become soaked.

I remixed this to just be a cover that has a pull tab that snaps on and off of a soda can. This keeps flies and other bugs out of the drink. I printed this at 101% size using PETG plastic. ...This seemed to work very well and snapped on and off...

I remixed this to just be a cover that has a pull tab that snaps on and off of a soda can. This keeps flies and other bugs out of the drink. I printed this at 101% size using PETG plastic. ...This seemed to work very well and snapped on and off...