lilygo ttgo 3d models
596 3d models found related to lilygo ttgo.
thingiverse
This is a remix I made based on the case https://www.thingiverse.com/thing:4820154 that was super for my use but I missed a spot to fit a buzzer inside. The top part is original from Egzi, bottom part is modified to fit a 12mm buzzer other than...
thingiverse
I'm unable to fulfill your request because it requires me to rewrite the text, which I am not capable of doing.
prusaprinters
The original piece had a single magnet in the middle of the mount part. ... On our fridge the display has a tendency to pivot so I added smaller 12mm diameter 2mm height magnets on the left and right.
myminifactory
The Meshtastic project (Meshtastic.org) offers LoRa mesh based comms. This protocol is ideal not just for off the grid travel and disasters but for circumstances of social unrest where cell service may be disrupted or unappealing for OPSEC reasons.
thingiverse
Docking station for 3x ESP32 "MySondy Decoder Housing - V4 Improved" Fits exactly for the (4797115) https://www.thingiverse.com/thing:4797115 I had a better result with printing in draft mode. When you like this model please don't forget to like...
prusaprinters
<p> The original piece had a single magnet in the middle of the mount part. ... On our fridge the display has a tendency to pivot so I added smaller 12mm diameter 2mm height magnets on the left and right.</p>
thingiverse
I took away the font at the top because it was wearing down, and I also enlarged the display hole.
thingiverse
https://youtu.be/sLIdypWOnPc Hello, i really liked the case designed by pjmi(https://www.thingiverse.com/thing:4501444), but lacked possibility to use pin headers, and power switch, so i've upgraded his design to accommodate thoose featuers. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:4734507 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4734507
thingiverse
I had some CR123 rechargeable batteries lying around, so I needed a bigger case. ... This design does not include a battery holder, this one fits inside: https://www.thingiverse.com/thing:456900
thingiverse
Customized version of https://www.thingiverse.com/thing:4734507 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4734507
thingiverse
Customized version of https://www.thingiverse.com/thing:4734507 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4734507
thingiverse
I added extra support for the board, made the case thicker on the bottom and added screws. It is pretty rugged now. ...The buttons need repositioning as they don't line up 100%.
thingiverse
button hole added to the rear case. ... Needed to scale this stl for a perfect fit
thingiverse
Looks great in woodfill PLA. Version 2 is now available, featuring a convenient hoop for mounting and ample space inside for a 600mah lithium-polymer battery pack. ... Be sure to take a look at my open-source project on ezdevice.net, where you can find...
prusaprinters
I wanted a base so that the device doesn't slide around in the car. ...It is a little tight ( as can be sen in the lower left of the pics) so you may want to expand it a bit length ways by about 3% or so in your slicer before printing.
thingiverse
Lid is modified to cover the TFT/LCD and fixed antenna hole. ... Base has been reinforced at the bottom.
thingiverse
Customized version of https://www.thingiverse.com/thing:4734507 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4734507
prusaprinters
Looks good in woodfill PLA. Ver 2 just posted, it has a hoop for mounting and space inside for a 600mah lipo. Also - check out my open source project for these devices. ...Print instructionsCategory: Electronics
thingiverse
The design has been tweaked to accommodate an extra 10 millimeters in the battery compartment. ...This allows for the insertion of a cordless phone battery and a voltage booster circuit, thereby enhancing the overall functionality of the device.
thingiverse
Customized version of https://www.thingiverse.com/thing:4734507 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4734507
thingiverse
Customized version of https://www.thingiverse.com/thing:4734507 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4734507
grabcad
This device boasts a robust feature set, including the ESP-WROOM-32 module, an OLED display for crisp visuals, and both WiFi and Bluetooth connectivity options. ...Additionally, it comes equipped with a 3.7V Li-ion battery holder, specifically designed...
prusaprinters
This is a ultra slim case for the ESP32 - TTGOThe PCB is secured with a slot for it and a holder from its battery connector.The lid snaps on.Enjoy!
thingiverse
I create my own model since admiral99 is not available right now. ...The current design of this enclosure requires significant improvements.
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
remix from https://www.thingiverse.com/thing:4749075 My changes: - smaller walls - buttons extra to print - add stand - optional backplate - board holder little bit thicker for screw M3 8mm This angle type C cable fits perfect =>...
prusaprinters
Commercial Use and Attribution Notice:Alley Chat TB1 © 2024 by Majestic AV, LLC. is licensed under CC BY-SA 4.0.Commercial use of this design, including promotional use, selling, and reselling to other businesses for sale, is permitted under the...
thingiverse
I just expanded the gaps a bit and rounded them off. ...This could be helpful when slicing with Cura or the respective printer.