lilygo 3d models

Jan's model was already very good. I had to adapt it because we only use BNC connectors and I did not want to use another adapter. Furthermore, I have installed magnets so that you can pin the receiver in a server cabinet on the wall. ... Magnete:...

We did this for a project and we needed to upload it quckly

Remix from https://www.thingiverse.com/thing:4770948 Better stand to prevent fall over.

One of those TTGO boards sold on Ali, with on-board 1.02 inches e-paper display.This one is bought barebone (no casing whatsoever) and sometimes comes with a bonus 16MB Qflash.As usual, I simplify the keepouts for aerials & small SMDs with red...

This remix lets you put the case on the table I changed corners. ... All the buttons are one 3d part now.

This is a chassis and cover for a meshtastic device with an m5 stack soldered on for standalone use without the need for a smartphone. Additional items needed:4 or 6 M3x8 screwsI would recommend printing on its side and using tree supports. I have...

One of those TTGO boards sold on Ali, with on-board 1.02 inches e-paper display.This one is bought barebone (no casing whatsoever) and sometimes comes with a bonus 16MB Qflash.As usual, I simplify the keepouts for aerials & small SMDs with red...

Case to hold a Lilygo vga32 with FabGl libaries and emulator to create this amazin PC compatible computer. ... Thanks Fabrizio your work allows us to create amazing devices.

For the LILYGO T5-4,7 inch eink/epaper display with LiPo Battery. 18650 battery model => https://www.thingiverse.com/thing:4901985 This angle type C cable fits perfect in combination with stand and standbase =>...

Small case for Lilygo T4 and a 18650 battery. few version on base allows several screen angles (and amount of space inside). battery on bottom for better stability. you need two M2 screws and heat inserts to secure device inside. ... here is link...

A frame designed for the LILYGO T5 4.7" E-paper Dev. Board which can be purchased here. Designed to accommodate an 18650 lithium-ion battery holder and includes cutouts for the USB-C connector, SD card slot, and reset button. ...The frame is assembled...

I used the Lilygo T-Beam with a 2.4" I2C OLED, the M5stack cardkb and a 18650 Li-Ion.You have to decide if you flash the Meshtastic Firmware: https://meshtastic.org/downloads/ or the just great LORA_APRS Firmware from richonguzman, link here:...

This is a case/stand I designed for my Lilygo 4.7" E-Ink display. I used a piece of the foam from the originally packaging in the back where the 18650 battery is housed in order to hold the board in place (see picture). Also the button on top has two...

This is a case/stand/holder I designed for my Lilygo 4.7" E-Ink display. The case is completely closed off to prevent dust from entering, with the exception of the charging point on the bottom. I'm using mine to display weather info that...

I designed this case for the "Lilygo T-Display-S3 Touch Development Board" which features a 320 by 170 color display and a touch screen. I'm planning on using this board in upcoming projects and decided to create this case for it. In order to learn...

This is a case is made to hold a "LILYGO TTGO ESP32 LORA OLED v1.0" developer module alongside with a rotary encoder. A case also provides place for a 18650 battery, a power switch and a buzzer. One handed operation is possible. The idea behind...

Hardware used: - LILYGO TTGO ESP32 LoRa v1.0 board (can be possibly modified for other models) - Short shaft rotary encoder (15mm plum handle) - Two panel mount push buttons (one is for the selection, the other is to replace the internal button)...

This is for the Lilygo T-Echo Communicator. I use it as a Meshtastic node that I can carry on me all the time to connect to nodes as I go around the place.There are two versions, one with the Quick Clip on the shell, and one without. Check out the...

This is a case/stand I designed for my Lilygo 4.7" E-Ink display. I used a piece of the foam from the originally packaging in the back where the 18650 battery is housed in order to hold the board in place (see picture). Also the button on top has two...

This is a case for the version 2 of the TTGO ESP32 LoRa development board with external antenna. Inside, you can fit a small LiPo battery. From the case, you have access to the Reset button, power on/off and the SD Card slot. You will need three...

remix from https://www.thingiverse.com/thing:4749075 My changes: - smaller walls - buttons extra to print - add stand - optional backplate - board holder little bit thicker for screw M3 8mm This angle type C cable fits perfect =>...

Instructables coming soon

If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. Thanks, Enjoy! https://www.youtube.com/watch?v=n6k_8D885sE This is a case for the version 2 of the TTGO ESP32 LoRa development...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This design mounts module using 5-10mm stands with M3 screws.

I just expanded the gaps a bit and rounded them off. ...This could be helpful when slicing with Cura or the respective printer.

The TTGO T-Journal features an OV2640 camera, an OLED display, several GPIOs to connect peripherals and a built-in programmer, which makes it easy to upload code.

Found this original Version on the ExpressLRS-Hardware Github (https://github.com/ExpressLRS/ExpressLRS-Hardware/tree/master/STL/SugarK-slim-slimmer-case) but for the DIY 2.4GHz by SugarK. But i had to modify this one to fit the ttgo_v2 module...

Watch the video for more information on construction and design. The body is screwed on with 4 m3x30 screws. On the contacts of the TTGO board, using a standard connector and a piece of a breadboard, the front buttons are assembled. The...

I like the original design by yamaha_xg but the bottom was a bit flimsy for me. I added a thicker portion to stiffen it up. OpenSCAD is your friend. My T-display S3 had no problems fitting but I had to print x and y at 99% on both my CR-10 and...