loading filament ender 3 v2 3d models

Webcam mount for Ender 3 V2 I used this HD Camera with Ringlight from Amazon Remark: You can open the camera at by removing the white light ring and adjust the focus. You only need to remove the glue on the thread. ... Category: 3D Printer Accessories

Turns out in the upgrade to the Ender 3 v2, they used a new part for the beeper which is a lot smaller than the original. So I replicated the design with the new sizes. ... The upper section cannot be any thicker (which would increase the sound...

Yet another fan guard for Ender 3 V2. I use it alongside my fan duct: https://www.thingiverse.com/thing:4754118 The inside cone is particularly wide to correspond to my front remplacement fan that has quite a wide center disk (12mm). ...I'd suggest...

Super Basic part to cover the screen on the new Ender 3 V2. Parts rest on the outer frame of the screen not the screen itself. ...I have both the plain screen cover and the cover with imperial logo that I printed for myself here.

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

Turns out in the upgrade to the Ender 3 v2, they used a new part for the beeper which is a lot smaller than the original. So I replicated the design with the new sizes. ... The upper section cannot be any thicker (which would increase the sound...

(Updated STP included) Full Stl file of ender 3 v2. Used for reference to do addons so you can see what your printer will look like before printing addons. By using tinkercad ect. ...you can now see your machine in full before printing the actual...

Ender 3 V2 Tension Caps Cap #1 goes in the front facing slot Cap #2 goes in the slot above the LCD screen May be a little snug, so you may have to wiggle the legs a little to loosen them

I made a flippable screen cover for the Ender 3 V2 screen since I haven't seen any designs like this I created my own. ...It's still very flimsy and not the greatest especially the clips on the side because they don't hold onto the screen too well.

Feet for ender 3 v2. They will give you extra 15mm ground clearance. They do not stick though, so if you lift the printer up they will fall. Also the rear left leg would normally colide with the psu cover, because of the hook for the cables. ...I have...

Este es una adaptacion de este modelo https://www.thingiverse.com/thing:5260591Los eslabones no son mios, El credito de los eslabones es unica y exlusivamente de https://www.thingiverse.com/arek_r1/designsLo unico que hice fueron unos pequeños...

Tool holder for Ender 3 v2. Slides onto the upper rail. Holds a pair of wire cutters on the end, plus tweezers, a wide spudger, 2 SD cards, 2 microSD cards and USB stick. ...I would recommend printing with support for the wire cutter holder

This is my version of the Cable chain for the Ender 3 V2. For the X till the print bed you need 11 cable mounts.For the YZ till Z mount you need 23 cable mounts.For the extruder till the hot end you need 16 cable mounts.So a total of 50 cable mounts...

Simple feet to adjust/level your printer, it fits the standard rubber feet of the Ender 3 v2. I use them with these risers https://www.thingiverse.com/thing:4665097 . It gains plenty of space for ventilation beneath the Printer. ...There is one version...

This is a 5.5mm endoscope mount that fits on the stock hotend fan guard of an ender 3 v2 printer. It has 2 parts. The clip that mounts snuggly to the hotend fan guard and the camera mount allows for angle and height adjustment. requires 1 M3x16mm...

Ender 3 V2 Filament roller using two 628 bearings. The two bearings sit on an axle which recesses into the roller shaft. The 628 bearings have an inside diameter of 8mm, so i made the axle 7.8mm diameter. If you use bearings with a smaller inside...

Useful links regarding the BLTouch: BLTouch Documentation: https://www.antclabs.com/bltouch-v3 Marlin Firmware (now configurable for Ender 3 V2): https://marlinfw.org/ Already configured firmware: https://marlin.crc.id.au/ Creality Firmware:...

A small Profile cover for the Ener 3 V2.

Updated to v2 - More hotend exhaust and bigger intake hole + cosmetic fix Added v3 - Round Style Duct and better performance This will fit on ender 3 V2 with Stock fan. After a couple test this duct design give me the best performance. If you use...

https://www.youtube.com/channel/UC5qbD7VqzdayIPZssbmtbMw Ender 3 V2 Board version v4.2.2 3Dtouch BIGTREETECH Smart Filament Sensor(runout sensor) Dual Gear Extruder Dual Z Axis Lead Screw Upgrade(Single Motor) anti backlash nut(T8)x2 Reinforced...

Check out this other print I made that goes well with this one when combined.Print settings:Layer Height = 0.2 mmInfill = 100%Perimeters = 3Temperature = 235C hotend / 70C bedThis is not my design but from someone over at Thingiverse that I couldn't...

This covers it and makes it more quiet you can still hear it just not as loud the ender 3 silencers are the same as this except the ender 3 buzzer is to big so this will fit the ender 3 V2. For some reason when I put it into creality slicer it...

Ender 3/3 pro filament Guide that will prevent the filament from breaking and bending. ...You will need a M4x16mm bolt and a 608 bearing

... this does not work with cr touch! if you want to use an auto bed leveling senor then you definitly want to use the original design(sastana duct for ender 3) and just print another crtouch/bltouch mount(still use the extra file for the blower fan)

It's nozzle holder for ENDER 3 V2. You can put 3 x 5 nozzles and the cleaner. The diameter of nozzle is 6 mm. You can easily pull the holder if you press on the holder. I used ABS material but you could use any materials. I used a nozzle with...

This is a project to replace all Ender 3 V2 mechanical endstops. So far I created only the Z, but I am working on the X and Y. * Z It is basically a remix of the original Creality support, it uses the extruder plate as the activator and...

When complete, you will need some M5 T nuts and M5 bolts to attach it to the Ender 3 frame. I opted to use M5x12mm T Screws, then added washers and M5 nuts on the outside to tighten securely. You will also require two M3 bolts to mount the sensor to...

A modified version of the standard Ender 3 V2 TrayIt accommodates a Raspberry PI Zero 2W, 40mm fan as well as space to house some of the original tools (nozzles etc)I added a V2 version, due to the realization that my tolerance on the width of the...

DISCLAIMER The GCODE is created exclusively for an ENDER 3 V2 and to be printed with a 0.4mm nozzle. If printed on another machine, or with a nozzle of different dimensions to the one mentioned, I cannot guarantee that it will come out right, let...

### **This now lives on [Printables](https://www.printables.com/model/347671-ender-3-v2-zaxis-stabilizer) and may not be up to date on Thingiverse** None of the existing z-axis stabilizers for the Ender 3 V2 fit correctly or used M5 bolts with...