logitech c920 tripod mount 3d models

Tripod and Arca-Swiss mount plate (for [Kurokesu C2](https://www.kurokesu.com/shop/C2_USBC) camera and C920 mk2 kit). ... Additionally needed: * 2x DIN912 M3x6 screws * 1x DIN912 M2.5x5 screw * L Allen keys

... ...My remix of it can be seen here: https://www.thingiverse.com/thing:3759353. This adapter removed the bottom pivot of the original model and replaced it with a pad featuring a tapped 1/4-20 hole to accept standard tripod mounts effectively.

Logitech C920 This camera requires extension and Mount A, and there is an installation video available online. PICam This camera comes in two pieces: front and back. There's also an alternate model designed by DAN TexasMan on Thingiverse. PICam...

I adapted several components from the linked C920 camera case (like fingers, camera cases, and joints). I crafted a part that attaches to the duplicator 6.\r\n\r\nFixed:\r\n Units are now measured in millimeters\r\n Interconnection spacing has...

Like many similar Logitech mounts, this mount replaces the hinge that attaches the camera to its stock mounting clip, so some disassembly of the camera body is required to install (plenty of video demos are available on YouTube). 8/16/2019 Update -...

Made a mount to attach Logitech C 920 webcam to a Creality CR10s pro V2. The mount just attaches by sliding over the extruder cradle. The webcam attaches by sliding into the end of the mount. No screws or adhesive tape required. The camera base...

Mount arm was too short for me. ...I extended the arm a bit.Also useful when combined with - https://www.thingiverse.com/thing:6303081

I found that the original mount bent under the weight of the camera, so I made it much thicker and it seems to stay straight so far. I found my camera was too low so I also raised the part where the camera sits. ...The clip part was a little too wide...

The mount should be printed vertically with the v-lock mounting rails at the bottom, to minimise the need for supports. I recommend using the 3mf file over the sty for more accurate printing. ... I hope this is useful, and please leave a comment...

This is a remix of the original design as when I tried it out the weight of the camera would cause the mount to lean back and then during printing fall off, I then tried an updated version with the bridges and that would not even hold its own weight...

This is a remix of the original design as when I tried it out the weight of the camera would cause the mount to lean back and then during printing fall off, I then tried an updated version with the bridges and that would not even hold its own weight...

I needed a solution to secure my camera without hogging valuable space on my work surface. ...This setup allows me to position it perfectly, giving me a clear view of my prints while also providing ample clearance for my printer's bed.

The device is designed specifically to support a Sony Handycam C270 camera, serving as a sturdy base for it to rest on.

High quality 3d model of Logitech HD Pro Webcam C920

I upgraded the setup by swapping out the mount for my Logitech C270 camera, replacing it with a newer model from vihapuu's collection - specifically the Logitech C920 mount. ...Now I get to utilize the advanced features of the C920 paired with Fredyp's...

To achieve this, consult the comprehensive disassembly instructions provided by iFixit at https://www.ifixit.com/Guide/Logitech+C920+Webcam+Disassembly/115077, which offers detailed procedures for safely removing the camera's casing and installing...

Remix of Robert Wallace's Tripod Mount, relocated mounting position to enable printing without supports. ...Cable clip struggles with my print, may require adjustments to effectively utilize it.

Just changed the dimensions to lower the Logitech C920 and fit my monitors (DELL 2423) better.

I specifically created this design to accommodate the C920 Logitech on RaffoSan's camera mounting system, but I recommend using https://www.thingiverse.com/thing:3013280 for a secure and long-lasting fit.

I only designed this to fit my C920 Logitech on RaffoSan's camera mounting system. ...Though for a better one use this https://www.thingiverse.com/thing:3013280 if you want a more permanent fit.

... ...So I made a 5/8" microphone stand thread in tinkercad and plopped it on the top of the this tripod mount adapter. Resulting in this monster, but it works both my camera and microphone are up off my desk thanks for my monitors included tripod mount.

Logitech C920/C930E Prusa i3 MK3/MK3S X-axis holder

Webcam Mount for Logitech C920: A Customizable Solution Mount your Logitech C920 webcam with ease using this versatile clamp bracket, designed to fit any M8 rod. The ingenious design allows you to print as many arms as needed to achieve the desired...

Mount your C920 webcam to your printer bed.

This is a Custom Pouch for Logitech C920, designed to work seamlessly with any GoPro Mount. It's specifically engineered to fit perfectly on top of the popular GoPro Mount found at https://www.thingiverse.com/thing:1620280. If you find this design...

This is a remix of [RaffoSan's Universal Camera Arm](https://www.thingiverse.com/thing:2477180), [Felwat's Swivel Adapter](https://www.thingiverse.com/thing:3013301), and [Felwat's Logitech C920 Adapter](https://www.thingiverse.com/thing:3013280)...

This is a custom mount that will fit almost perfectly a Logitech C920 Webcam. ...Simply attach it to the inner corner of your IKEA LACK enclosure at the desired height using superglue, then fine-tune any remaining adjustments from the webcam's built-in...

However, the Logitech C920 and C930 webcams really don't have a wide range of tilt angles up and down. To assist with this, I designed a clip-in holder that holds the hinged portion of the webcam so you can really point it in just about any...

... This design is compatible with a standard 1/4-20 screw-mount tripod, just like you would use for a camera - but don't over tighten it! This design should print smoothly without any supports if the side where the screw inserts lies flat on the bed.

a simple privacy cover for logitech c922 and c920 you can print it without supports use some 1.75mm filament for the hinges