logitech camera c270 3d models
113122 3d models found related to logitech camera c270.thingiverse
Nice Stand for your Logitech C270 Camera Uses 2 3mm screws and nuts.
thingiverse
Logitech C270 Camera Mount that will work with TeachingTechs' Flexible webcam mount for Octolapse
thingiverse
Logitech C270 Camera Holder for LED Lamp you can buy here: https://www.ebay.de/itm/255143207450
thingiverse
Remix of IgorF2's articulating lamp (https://www.thingiverse.com/thing:2505394). ... I wanted a mount for my Logitech c270 camera. ...
thingiverse
Well this camera mount is a hassle free way to mount your C270 to anything! Disassembly of the camera module is not required! Simply take off the stock mount, and slide it into our 3D printed case. ... Want the STEP file email us at...
thingiverse
These parts are for standing a Logitech c270 Webcam on any flat surface! The camera can tilt vertically already, and the "holder" can rotate horizontally on the "stand" easily, but with enough friction to hold after positioning. ... The "feet" are...
youmagine
These parts are for standing a Logitech c270 Webcam on any flat surface! The camera can tilt vertically already, and the "holder" can rotate horizontally on the "stand" easily, but with enough friction to hold after positioning. ...The "feet" are...
thingiverse
This faceplate allows you to use a screw pressing on the top and the bottom to adjust and lock in the angle of a Logitech c270 camera. To mount pull off the cover of the camera and take out the 3 screws then take off the plate the screws were...
youmagine
Fits a Logitech C270 webcam and a Prusa i3 made by Schufco. ...Connect the webcam to Octoprint for timelapse videos and monitoring your print.
thingiverse
This is a mount for the camera Logitech C270. You only need a rod with diameter M8. I use a threaded rod in the picture, as this is available in any hardware store. Just when using a long rod conventional mounts tilt because of the leverage. ...
thingiverse
A very small remix of an already excellent camera mount. Modifications are 1. Base modified to use 9.5 x 3mm neodynium magnets 2. C270 Mount angled to 90 degress for better up/down movement. ... Enjoy!
thingiverse
Original Model: https://www.thingiverse.com/thing:2281259 Changes in the model: - Mount the camera for printing on the side. - Quick fastening to the bed with a bolt. ...
prusaprinters
Easy to print Camera Mount for the MK3.Print settings:Material: PLA / PETG / ASANozzle: 0.6 mmPerimeters: 3Layer Height: 0.2 mmNo supportsInfill 20 - 30 %
thingiverse
This is a remix, adding a retrofit for LogiTech C270 (with Raspberry Pi for example) and a piece to mount it on a 3D printer frame.
prusaprinters
This is a remix, adding a retrofit for LogiTech C270 (with Raspberry Pi for example) and a piece to mount it on a 3D printer frame. Print instructionsCategory: 3D Printer Accessories Summary This is a remix, adding a retrofit for LogiTech C270 (with...
cults3d
Hi, I was thinking about how to mount a Logitech C270 camera to a wall on a Raspberry Pi in a printer booth, and tilt -and- tilt in multiple ways. This set consists of: wall holder_long arm 1 arm modular 4th arm modular 2 wall bracket_short With...
thingiverse
Print each part in zip file once, and assemble with the hinge screw from the C270 hinge and 10 X 3/4" machine screws for the joints. ...Feedback is welcome!
thingiverse
Could not find a top-down view mount for my Logitech 270 webcam for Octoprint. I went ahead and created one. You utilize the existing Logitech pin and screw so don't lose them. Few seconds to mount the camera and few seconds to install. ...Slides in...
thingiverse
Inspired from many other camera mounts that i found on the web, i finally design this and i hope that can fit your needs too!! ... Enjoy!!
cults3d
Had a hard time getting my camera to mount to the Creativity ELF Printer, so I made this mount to clamp the camera to the top frame. ... 2 M5 screws are used to hold it in place, no issues with contact or wobble so it's a winner.
thingiverse
Had a hard time getting my camera to mount to the Creativity ELF Printer, so I made this mount to clamp the camera to the top frame. ... 2 M5 screws are used to hold it in place, no issues with contact or wobble so it's a winner.
prusaprinters
I did put a drop of super glue inside the holes to help hold them in place as the magnets are very strong and they would pull out when trying to separate. Print as many wall plates as you need to move the camera around your enclosure. link to the...
thingiverse
C270 Logitech Kamera Ständer Benötigt wird 1x M3x30 Schraube 1x M3x16 Schraube 2xM3 Mutter und 4x M10 Mutter zum beschweren des Fußes
prusaprinters
This is a mount for the logitech C270 camera to the post of a lack enclosure.
pinshape
This is a tripod mount designed for the Logitech C270 Webcam. The mount makes it easy to record your print or easily set up a camera for live-streaming! Print Settings - Printer: Raise3D N1 Rafts: Doesn't Matter Supports: Yes Resolution:...
thingiverse
This mount was designed for the Logitech C270 Webcam in order to thread onto an articulating arm, in this case to view a 3D print remotely. After the file has printed, the large hole in the bottom will need a 1/4"-20 heat-set insert that is 0.5"...
thingiverse
This is a Mount for the Logitech C27 camera for the Anet AM8 aluminium frame
thingiverse
This is a tripod mount designed for the Logitech C270 Webcam. The mount makes it easy to record your print or easily set up a camera for live-streaming! Print Settings Printer: Raise3D N1 ...
thingiverse
This is a webcam holder for my logitech webcam with a LED strip light. Needs some more specially in the part where the camera holds. And I think I will make another but this time with more space for 2 rows of led lights. More Light??? yes.. ...this...