logitech ergo k860 3d models
6906 3d models found related to logitech ergo k860.thingiverse
Lost your battery bay cover for your Logitech ERGO K860? ...Here is an accurate measurement model.
thingiverse
If you use a Logitech Ergo K860 Wireless Ergonomic Keyboard and put to much pressure on the 7y degree leg, you can snap it off. This happened to me, so I modeled up a replacement. For FDM I added a little snap off support for the pegs, so it...
cgtrader
3d model Ergo K860 Wireless Keyboard designed and manufactured by Logitech. Ergo K860, a split ergonomic keyboard designed for better posture, less strain, and more support. A fluid and ultra-precise typing experience with no compromise in speed and...
thingiverse
This stand add some additional degrees of tilt to your MX Ergo for extra comfort. The gray one has 10 degrees of tilt, just like the one included with the MX Ergo Plus. The black version has 15°. I highly recommend to stick some rubber or...
thingiverse
New shape 100% fit my hand in a neutral position Mouse used was a Logitech M510. The shape was created by adding playdough around the mouse then placing my hand on top and removing / adding material until comfy. ... Shape was then 3D scanned using an...
thingiverse
A replacement battery cover for a Logitech Ergo M575 trackball.
thingiverse
https://www.logitech.com/en-au/product/mx-ergo-wireless-trackball-mouse The new mouse is great, and perfect for my work though it is quite a bit heavier and more aimed at user who are sitting at a desk whereas the M570 was quite light and was very...
thingiverse
To clean the little ball bearings of a Logi MX Ergo trackball, you have to remove the ball. A pen doesn't fit and using a screwdriver can damage or scratch the ball which renders it unusable. ...Hence this tool I FORGOT;: USE 100% FILL, OTHERWISE IT...
thingiverse
This is an all in one solution for your Logitech MX Ergo. The mouse sits at 45°. It uses the original metal base and is held on with up to 6 10x2mm magnets (you only really need 3) and it's recessed so there's no risk of the base sliding off. The...
thingiverse
Wedge designed to increase by 15° the side tilt angle of trackball Logitech Mx Ergo. Printing: I decided to print in TPU for 2 reasons : 1) Better adhesion on the surface. 2) Easier insertion of neodymium magnets. I don't try with PLA...
thingiverse
25deg tilt for better ergonomics for a old logitech trackball wheel mouse for my home office. ...Attach to the mouse with tape.
prusaprinters
The original Thing is very nicely designed (in particular the MX Ergo fits nice and snugly into the stand), but perhaps I have larger hands than normal, and I found it hard to rest the mouse in my palm while accessing the ball and wheel (see last...
thingiverse
The original Thing is very nicely designed (in particular the MX Ergo fits nice and snugly into the stand), but perhaps I have larger hands than normal, and I found it hard to rest the mouse in my palm while accessing the ball and wheel (see last...
thingiverse
remixed from "Logitech MX Ergo Stand" https://www.thingiverse.com/thing:2640807 and "Logitech Ergo MX Dongle Storage" https://www.thingiverse.com/thing:2802676
thingiverse
ergo Logo 10x10cm hey guys realy apriciate a photo of your version / remix lots of love Tempest1991 Post A Make
thingiverse
This model is an evolution of https://www.thingiverse.com/thing:2841421#Summary First of all, Thanks for sharing it. I added: * Hole and stick to remove the ball. * The holes to insert the ferromagnetic plates are replaced by circular ones...
thingiverse
Logitech MX ERGO 20° degree base + Trackball key This base adds a 20° to the Logitech MX ERGO mouse for a more comfortable vertical position. The metallic base of the mouse should be placed first, it fits tightly with little pressure and a nice click...
cults3d
... fit my motion rig. Pretty specific usage, but sharing f3d in case you want to modify. I used the Logitech MX Ergo design (thanks!). ...Added a modification to insert a 30mm x 19mm x 2.4mm metal plate so I did not have to add glue or anything else.
thingiverse
... fit my motion rig. Pretty specific usage, but sharing f3d in case you want to modify. I used the Logitech MX Ergo design (thanks!). ...Added a modification to insert a 30mm x 19mm x 2.4mm metal plate so I did not have to add glue or anything else.
thingiverse
This remix is of 15° Logitech MX Ergo trackball mouse base that will bolt to 40 series aluminum extrusion with 2x M6 bolts. You can use Industrial Strength Velcro Tape to mount the mouse to the base. ... Additionally required: 2x M6 bolts 2x M6...
prusaprinters
This is a remix of darknao's 15 degree Logitech MX Ergo Mouse Base (https://www.thingiverse.com/thing:2640807) for 40 Series Aluminum Extrusion. It can be mounted with 2 M5 bolts. ...It's recommended to use Industrial Strength Velcro Tape to mount the...
thingiverse
4 degree leg for K860 keyboard. ... Patte de 4 degrés pour le clavier K860 de logitech. ... Link for 7 degrees leg / Lien pour la patte de 7 degrés : https://www.thingiverse.com/thing:5145353
prusaprinters
based on the dongle storage piece by dlofstrom, this adds a stick to remove the trackball for cleaning, storage for the stick, and places to mount magnets so it's less messy when taking it apart. ErgoMXDongleStorage.stl is the original piece, only...
thingiverse
... to mount magnets so it's less messy when taking it apart. ... ErgoMXDongleStorage.stl is the original piece, only needed if you want to use the openscad file. otherwise, just print mx_ergo_wedge.stl and mx_ergo_stick.stl (I did this one solid). ...
prusaprinters
This is a simple print that I used to replace the 4° tilt foot on my Logitech K860 keyboard. I don't know if it will work on other keyboard's but it does fit this one well. I printed this with a 0.2mm layer height quality with 20% infill. It took 12...