logitech k750 key replacement 3d models

This is my initial draft, Measurements obtained from an antique key suggest a possibility that the attachment gap at the bottom may be either excessively narrow or unacceptably wide - only time will tell.

Summary This Remix Boasts a Reimagined Take on Yangsong's Key, Still Evolving to Perfection. ...A Solid Foundation is Provided by Printing at 100% Infill with Strategic Use of Raft Support, Alongside an Optimal 10% Support Structure.

This is a beefier version of the Olivetti Lettera 22 key. This is a tight fit so you'll probably need a pair of pliers to convince it to get in place. I print this in black ABS. So far, so good. ...It doesn't have the finger cup yet but that may come...

Use this model with the inner part of your old Carisma key, ensuring a snug fit to prevent looseness. The top section is designed to require no adhesive, simply press firmly until it clicks into place. ... The print itself requires no additional...

Purchase replacements for around $5 each including shipping or print your own at just $1 per piece. The design accommodates two 1/4" diameter x 2/10" thick magnets. During printing, pause the process at a z-position of approximately 12mm, insert the...

I designed replacement feet for my trusty MX518 mouse, and they fit other Logitech mice too. The original feet on my beloved MX518 were badly worn out, so I took matters into my own hands. These new feet are working great so far. ...To attach them to...

... (two Left, two Right). - 8 M3x8 Screws - 8 M3 Nuts - T5 Torx Screwdriver - small Phillips screwdriver - Allen key for the M3 screws - a plastic Opening Picks (optional) - soldering iron to desolder the cable on the two PCB's (easy !) Have Fun ;-)

Print this replacement part to experience a brand-new, silky-smooth joystick feeling once again. DISCLAIMER: the original bushing is ridiculously smooth and boasts low-friction properties. If you print with PLA, it's tough to match these...

Replacement buttons for Logitech gamepads. Buttons have inserts for the symbols so you can print them whatever colors you like. The inserts are undersized 0.05% so are a tight fit. Best way to install them is press them into position by rolling the...

So I have made replacement front cover for Logitech C170 that can accommodate my new lens. Since I don't have any need for microphone I have left it inside covered with new cover, but if you want to keep that option you can drill 2-3 small holes...

My Logitech G433 was broken on both Pivot Points, but i can't find Spareparts for the G433 :-(. Here are my printable Spare Part's ;-) You need: print all four Parts (two Left, two Right). 8 M3x8 Screws 8 M3 Nuts T5 Torx Screwdriver small Phillips...

My friend Alex misplaced one of his Logitech WingMan Rumble Pad's detachable analog sticks, so I decided to recreate it using OpenSCAD for my first project. This led me to write about the process on the Ponoko blog, which you can find here:...

This is my cover replacement for Logitech C270 Webcam. All you need to do is disassembly the original webcam and remove PCB electronics board. The board is fixed in the new housing using the original screws.</p><h3>Pros</h3><ul><li>Click-clack...

Maybe they fit for other Logitech mice too.The original feet of my good old MX518 were battered, so i simply designed these. They work well so far. I use 468MP adhesive for glueing them to the mouse.</p><p>I used ABS, but i think PLA or PETG got a...

Therefore, by replacing the case, the attachment part can be freely designed to ensure strength.Objective 2Kenko REAL PRO Multi-Coated Glass REAL PRO 0.4x Super Wide Angle Clip Lens for Mobile Devices, Black (KRP-04SW) so that you can check a wide...

This is my custom cover replacement for the Logitech G720 Webcam. To install it, you'll need to disassemble the original webcam and carefully remove its electronics PCB board only. The new PCB is securely attached to the inside of the cover using...

Confirmed as working with the Logitech K120. ...It may work with other models but not tested - it's 15mm wide. Ideally print with supports for the hinge pins.PLA is probably sufficient but PETG or greater is recommended.

key cap left ctrl - Tecla Ctrl izquierda Logitech G413..

After trying the replacement ear holder screws and watching them fail as well, I was desperate for something more substantial. That's why I went on the hunt for better alternatives and lost some of the original screws in the process. To ensure that...

Подставка для клавы Logitech

Just a quick sketch I whipped up in Fusion 360 - still working on getting the STL file dialed in though!

ABS NOZZLE TEMP 230 BED TEMP 110 HIZ 0.50

Logitech's Extreme 3D Pro Joystick Takes Gaming to New Heights

Logitech MX ERGO 20° degree base + Trackball key This base adds a 20° to the Logitech MX ERGO mouse for a more comfortable vertical position. The metallic base of the mouse should be placed first, it fits tightly with little pressure and a nice click...

... This piece does work on FDM printers and can bring a broken key back to life. This project was specifically designed for a Logitech K800 wireless keyboard, but may also work with other keyboard models that feature a similar style of key hinge.

First thing I do when I get a new keyboard is rip out the 'windows' key and the 'list' key because they're always getting in the way of my gaming sessions. Problem solved, but now I've got a brand-new problem: dust starts collecting in the keyboard's...

A rough replacement for the K295 keyboard, made to fit the left ALT key. Will probably fit others as well, or can be adapted to fit. I think the other keys are a bit smaller, so maybe shrinking it would help. This object was made in Tinkercad.

Garage door remote control replacement key hanger

Slightly better key fob replacement for broken F-150 keys.

I did this Key Cover "Renault Menage II Key Cover - Replacement" on Fusion360.