logitech mx master 3 and space mouse carrying case by 3d models

I left a gap for the USB port and the SD card slot of the display.I used a 3.2inch ILI9341 TFT LCD Touchscreen and use a board like this one Printing:No supports0.4mm Nozzle0.2mm Layer HeightI printed it in PETGMaybe later I will publish my firmware...

I was searching for a Raspberry Pi 3 case to house my Home Assistant controller, and I wanted it to fit perfectly next to my upcoming Akita Smart Home. You can read about it on Kickstarter; its shape is essentially a tilted hexagon pillar:...

Similar dimensions of the set sold by Ortur for $80.These have the option for reusing the original feet as well. Use a 25mm M5 bolt  with M5 hex nut for securing legs to bracket.Use 8mm M4 bolt for securing bracket to frame.Reuse the original screws...

... in 3D Max 2017. ...It features general maps with added masks for materials. However, note that the model only includes the external shell; internal components and details are not included. ...The file formats available are MAX, FBX, OBJ, and MTL.

<p>Easy to print. ...I used PLA but I guess PETG would work also. Tested and the fit was perfect.&nbsp;

Inside the case, there's plenty of room for wires and a bit of other stuff. For attaching the Arduino and the lid, use small self-tap screws. Two marks are made on the case for cable drill holes. This ensures that they'll be in the same place...

The measurements for the mounting and frame are precise, but those for the blades are incorrect. ...Check out this product here: https://www.newegg.com/Product/Product.aspx?Item=N82E16835129065

Extended height foot increases airflow from the bottom. ...Total height is 18.5mm, compared to around 8mm stock. To edit the design, visit onshape.com and access the public document. ...The document ID is 515a01c6f666f557669986df.

After seeing the original on Adafruit's Retro Tech https://www.youtube.com/watch?v=pTRtiaqFQyQ, I decided to try and make it. ... It's not perfect but it should go together

EDIT (09.22.19) Added storage boxes on the front of the printer and a cover without inscriptions Display cases for Ender 3 and BIGTREETECH TFT35 V1.2 control panel TFT 3.5 v2 https://www.thingiverse.com/thing:3614877 IMPORTANT: I ​​will be very...

Display cases for Ender 3 and BIGTREETECH TFT35 V1.2 control panel TFT 3.5 v2 can be found at https://www.thingiverse.com/thing:3614877 I would be very happy if you gave me your photos here. ... If you enjoyed this project and want to say thank you,...

To install the pi angle the usb and ethernet ports in, just past the front, then push down on the long side opposite the power and HDMI, then push down the side that had the power and USB and it should snap into place 3. Attach your pi cam cable and...

So I designed two custom frames / holders suitable for the Cobalt RAQ 3, one for the RasPi and one for a 2.5" disk (to be mounted in the Cobalt disk frame). The RasPi is securely attached to the holder using self-tapping screws. ...On the lower right...

Here is my case for the Eryone Thinker S to fit an SKRv1.3, raspberry pi3 and 3 Lm2596 buck converters. I use one buck converter to power the Pi, one to power the stock 5V heat break fan and the 3rd one for future upgrades like some 12V leds for...

It currently supports phone case mode, Razer Junglecat rails, and Switch Joy-con rails. I'm working on the electronics for a USB-C gamepad using an Atmega32u4. The phone case uses OpenSCAD to customize the case and build STLs. It supports the Pixel...

This is a custom Raspberry Pi camera case and arm for the Ender 3 printer, optimized to work seamlessly with OctoPrint. Some minor adjustments may be needed to ensure a snug fit between the arm and the bed support - a little sanding should do the...

My Pieces for Space Cases They Say I'm Crazy

... ...Allows you to attach the camera to a ball and socket chain for better positioning. An M3x25 screw and nut connect the camera to the mount to replace the original Logitech stand. ...(The screw only needs to be > 16.5mm, 25mm is not necessary.)

I intended to install my bracket onto the y-rail but discovered that the connector was slightly too short. ...I therefore decided to extend the shaft by approximately 20mm.

Bearing housing for Logitech G25, G27, G29, G920, G923 The common problem with the Logitech wheels is the bearing housing. I designed the bearing house, because the original one is broken under 1 year. I made it for cnc milling machine. I attached...

Want to save weight and don't use the side buttons on the right side of the mouse? Then this mod is perfect for you! So get your 3D printer ready for some juicy printing! It's non destructive and looks completely stock from the outside. It's held...

To securely hold the GoPro, a 15mm wide velcro strap approximately 160mm in length is required for strapping into the case, utilizing an ImmersionRC Strap being used by us previously. In addition to that, 15-20mm Velcro straps around 100-150mm long...

https://www.thingiverse.com/apps/customizer/run?thing_id=40703 Using the following options: case_pattern_shape = custom_shape case_pattern_rotation = opposite_orientation case_pattern_radius = extra_large_circle case_case_thickness = standard_size...

This timelapse webcam mounts on the y axis rail and takes fabulous time-lapses that are in frame. ....

This is a case and mounting bracket system for the Panda Pi Display for the Ender 3 printer using the Panda Pi controller board. ...The default user interface for the Panda Display is landscape mode so you would normally use the landscape mounting...

Support plate and case for raspberry pi 3 model B: the support plate is pierced to allow a sturdy wall mounting (or other uses). The support plate is inserted in the housing on a rail designed for this purpose. ...Models drawn with OpenSCAD are printed...

This custom design builds upon https://www.thingiverse.com/thing:2799219, enabling seamless use of the NavoLabs Raspberry Pi 3B+ POE Hat with this case. ...The base components remain unchanged for users who have already printed the original version,...

I managed to find a c270 at the thrift store and decided to remix the previous mount for this camera as well. You will need a M3x16 to attache the camera to the mound and a M3x8 to lock the mount in place. ...I also used a ziptie to get the cameras...

... the current state, the modified setup works temporarily. The human plans to further modify the arm to make it stronger and print it with less infill, allowing for a secure connection via a wingnut that takes advantage of the interior 2020 channel.

It works, but only with the Ender 3 Pro.: Compatible with Ender 3 and Ender 3 Pro. Uses minimal filament and prints without support. Factory mounting hardware is retained. Two lid pieces snap together for easy, hinged access. Fan is moved to the...