logitech speaker stands 3d models
261190 3d models found related to logitech speaker stands.
thingiverse
... ... These stands are designed to raise a 50" LG TV 25mm (1 inch) to clear a SONOS Beam or SONOS soundbar but can be scaled to fit your preference. I have included the SketchUp file for scaling, but the STL file can also be scaled in your slicer.
prusaprinters
As seen in my workspace redesign video above…Simple two piece wedge style speaker stand design. Trim piece snaps into the wedge and you can add some glue to be sure it doesn't move.Edifier R1280 are great budget friendly near field speakers for your...
prusaprinters
I created some stand to tilt the Edifier r1280t a bit. I looks much better now (i think) Please note that i made them a little to deep so a small edge showed at the front. I stuck a piece in to thicken the back a bit so the front edge alligns You may...
thingiverse
A basic, but sturdy, phone stand I made for my partner's iPhone. Works great with my phone too. Added ports so the sound isn't muffled. When I open it in Cura, it's 10x smaller than it should be, exactly. ...I must add a zero to make the size 1000%...
thingiverse
I designed some stands to adjust the Edifier r1280t just right. It looks much better now, I'm sure of it. Please keep in mind that I made them slightly too deep, so a small edge shows at the front. To fix this, I added a reinforcement to thicken the...
thingiverse
I designed my own sonic stands after printing one from Blackbird2016's design on Thingiverse, which I found at https://www.thingiverse.com/thing:1804269. I wanted to create something similar but original before sharing it with others. The design is a...
thingiverse
Support for wall mount for Logitech Z506 5.1 surround sound speakers.
thingiverse
Holder for the Logitech Z407 speakers Fit on the Ikea Vitval's desk
thingiverse
### Assembly Mounting holes were adjusted to reuse hardware from the Logitech Z313 system, so the speakers should be secured with M3 screws and the lid should be secured with M2.5 screws. If you find the fit is too tight, adjust the horizontal...
prusaprinters
So I've quickly, made a stand for Logitech C525 webcam to make it a makeshift Document Camera. You can insert the leg of the camere just into the slot of the stand --- then the image orientation will "upside-down" in your SW by default. ...You can...
thingiverse
So I've quickly, made a stand for Logitech C525 webcam to make it a makeshift Document Camera. You can insert the leg of the camere just into the slot of the stand --- then the image orientation will "upside-down" in your SW by default. You can...
prusaprinters
So I've quickly, made a stand for Logitech C525 webcam to make it a makeshift Document Camera.You can insert the leg of the camere just into the slot of the stand --- then the image orientation will "upside-down" in your SW by default. ...You can either...
thingiverse
Luckily, someone has shared the mesh file for those dodgy legs, so we can 3D print our own stable stands.\n\n\nHere are some basic instructions:\nWhen using PLA or ABS to create this stand, you'll be fine either way. However, I do prefer ABS because...
cults3d
You can print small holder for IKEA Omar stand as well and fit it onto speaker case. Fusion360 file included. Speaker i have used: https://www.aliexpress.com/item/4000335140261.html?spm=a2g0s.9042311.0.0.27424c4ddo4fXP Easy print, i have used some...
thingiverse
You can print small holder for IKEA Omar stand as well and fit it onto speaker case. Fusion360 file included. Speaker i have used: https://www.aliexpress.com/item/4000335140261.html?spm=a2g0s.9042311.0.0.27424c4ddo4fXP Easy print, i have used...
prusaprinters
Keyboard stand for Logitech G915/815 and TKL versions (and basically any other that has the same dimensions on the lower part).Needed some extra space when using my tablet.Might be a good idea to glue some rubber feet under the holder for some...
thingiverse
It's tailored for my Logitech 6930 wireless headphones, which come with a USB extender dongle, but could likely be scaled down to fit smaller headphones as well. I aimed to make it printable without the need for supports. Printing this model takes a...
thingiverse
This is a modification of my original Logitech MX Ergo Mid Body Stand 45° with the difference being an additional 20° tilt. It uses the original metal base and is held on with up to 6 10x2mm magnets (you only really need 3) and it's recessed so...
thingiverse
Added a base area as speakers were not super stable Added two supports in the back