logitech unifying receiver replacement 3d models
221984 3d models found related to logitech unifying receiver replacement.
thingiverse
If you're like me, and your top clip just snapped off, don't worry - you can easily replace it with this part. First, print both parts and assemble them later. For optimal results, use ABS with Acetone treatment. You'll also need to remove the extra...
pinshape
If your lower clip retainer has broken as well, please see my other available part for replacement. ... For more information or to download the design files, visit: http://www.thingiverse.com/thing:734999 Update: I made some changes to the clip2_part2...
thingiverse
Logitech K270 / K260 / MK270 / MK260 / MK270r Replacement Foot Stand
thingiverse
Stronger than original Logitech replacement clamp.Working thread, no need for supports.
thingiverse
This bracket holds the ear piece assembly to the head strap. It contains a tiny fork that locks the earpiece shaft in place. The right hand ear piece had fractured into pieces on my son's head phones. Modelled the left part, mirrored to left, printed...
thingiverse
Get a replacement tilt leg for your trusty Logitech keyboard, model K235 or MK235, at an unbeatable price - just $7.99 less on eBay when you buy two!
thingiverse
Replacement clamp's thickness for Logitech Driving Force GT Useful to fix the steering wheel to thin desks I created two version for 1 cm and 2 cm (like the original) Enjoy :-)
thingiverse
I designed replacement feet for my trusty MX518 mouse, and they fit other Logitech mice too. The original feet on my beloved MX518 were badly worn out, so I took matters into my own hands. These new feet are working great so far. ...To attach them to...
thingiverse
Print this replacement part to experience a brand-new, silky-smooth joystick feeling once again. DISCLAIMER: the original bushing is ridiculously smooth and boasts low-friction properties. If you print with PLA, it's tough to match these...
thingiverse
Replacement buttons for Logitech gamepads. Buttons have inserts for the symbols so you can print them whatever colors you like. The inserts are undersized 0.05% so are a tight fit. Best way to install them is press them into position by rolling the...
thingiverse
So I have made replacement front cover for Logitech C170 that can accommodate my new lens. Since I don't have any need for microphone I have left it inside covered with new cover, but if you want to keep that option you can drill 2-3 small holes...
prusaprinters
Maybe they fit for other Logitech mice too.The original feet of my good old MX518 were battered, so i simply designed these. They work well so far. I use 468MP adhesive for glueing them to the mouse.</p><p>I used ABS, but i think PLA or PETG got a...
prusaprinters
This is my cover replacement for Logitech C270 Webcam. All you need to do is disassembly the original webcam and remove PCB electronics board. The board is fixed in the new housing using the original screws.</p><h3>Pros</h3><ul><li>Click-clack...
thingiverse
My friend Alex misplaced one of his Logitech WingMan Rumble Pad's detachable analog sticks, so I decided to recreate it using OpenSCAD for my first project. This led me to write about the process on the Ponoko blog, which you can find here:...
prusaprinters
Therefore, by replacing the case, the attachment part can be freely designed to ensure strength.Objective 2Kenko REAL PRO Multi-Coated Glass REAL PRO 0.4x Super Wide Angle Clip Lens for Mobile Devices, Black (KRP-04SW) so that you can check a wide...
thingiverse
This is my custom cover replacement for the Logitech G720 Webcam. To install it, you'll need to disassemble the original webcam and carefully remove its electronics PCB board only. The new PCB is securely attached to the inside of the cover using...
prusaprinters
Confirmed as working with the Logitech K120. ...It may work with other models but not tested - it's 15mm wide. Ideally print with supports for the hinge pins.PLA is probably sufficient but PETG or greater is recommended.
thingiverse
My Logitech G433 was broken on both Pivot Points, but i can't find Spareparts for the G433 :-(. Here are my printable Spare Part's ;-) You need: - print all four Parts (two Left, two Right). ... - 8 M3x8 Screws - 8 M3 Nuts - T5 Torx...
prusaprinters
My Logitech G433 was broken on both Pivot Points, but i can't find Spareparts for the G433 :-(. Here are my printable Spare Part's ;-) You need: print all four Parts (two Left, two Right). 8 M3x8 Screws 8 M3 Nuts T5 Torx Screwdriver small Phillips...
thingiverse
After trying the replacement ear holder screws and watching them fail as well, I was desperate for something more substantial. That's why I went on the hunt for better alternatives and lost some of the original screws in the process. To ensure that...
thingiverse
One of the folding legs on my K270 keyboard snapped, so I crafted these as a substitute.\nAdded a 10mm longer version for a more dramatic keyboard incline.\nI utilized PLA but ABS should work equally well.\nPrint Settings\nPrinter: \n ...
thingiverse
a remix of logitch keycap k270 What did i change? ... i removed te tiny lines above and under the circle in the middle to make it easier to print
thingiverse
K330 keyboard leg. ...Printed on my Ender 3 V2 with no supports and fits perfectly.
thingiverse
Headset arm or bracket is a derivative from design: 3042398 Retaining braced is brand new and improved complete re-design Video featuring repair process: https://youtu.be/3mW9i2OuxFw If you like more 3D printing and DIY videos please...
prusaprinters
<p>Saves some weight. ...Don't do it it's useless.</p>
thingiverse
https://www.thingiverse.com/thing:4974267 IT IS HIGHLY RECOMMENDED THAT YOU REPLACE BOTH SIDES OF THE CONNECTOR WHEN YOU REPLACE THIS PART. IF NOT, THE CONNECTION MAY BE A BIT ON THE LOOSER SIDE. Inferno is in progress. ... Feedback is...