logitech webcam privacy cover 3d models

Slide privacy cover for Logitech C270 webcam

Simple privacy cover for the Logitech C270 webcam to clip over.

Simple privacy cover for the Logitech C270 webcam to clip over. Category: Computer

Privacy cover for your Logitech webcam printed in two simple parts. There is an inner channel on the webcam cover that receives the slider to prevent it from ejecting during operation. Depending on your print quality, some sanding and lubricant...

I could not find a good privacy cover for the Logitech C910 webcam, so I made my own. This thing is heavily influenced by the excellent [C920 privacy cover](https://www.thingiverse.com/thing:2003903) by...

Didn't seem to find a cover for the C920 so made one with inspiration from another user.Recommend using the improved version of the cover which fits better to the camera. Logitech C920 privacy cover improved by siamigo | Download free STL model...

Slide privacy cover for Logitech C270 webcam Print Settings Notes: Print cover upside down - track facing up.  Print slider right side up - front sticking up.  Rafts: No  Supports: No  Resolution: 0.2  Infill: 25% Assembly Place cover on cutting mat...

I could not find a good privacy cover for the Logitech C910 webcam, so I made my own. This thing is heavily influenced by the excellent C920 privacy cover by OnlyTono. The privacy cover consists of two pieces. The base goes on top of the cam and...

This is a simplified printable web cam privacy cover for the new Logitech c525. This project is properly positioned for printing. No supports required. Hope this works for your camera too. ... Enjoy.

Decided to make my own webcam cover that could easily be shifted to the side with literally one finger to uncover the camera lens. There is one file with rounded (chamfered) edges which might require supports (My 3D printer didn't need supports). You...

Something to cover up my lens.

... one cover. ...A it differs from others. On opened state cover laid horisontlly. Designed to be printed on a side separately. (I've tried print it assedmbled. No success) Please place parts as shown on picture. ...Supports should be turned on.

Printed out on Photon S using clear resin, used 1.7mm clear filament as hinges per authors instructions. ...Works Great!

Not the thinest possible design. I'll try to improve it in the near future and then update this one. But for now, this does the job quite well ! ...Print Settings Printer: Da Vinci 1.0 AiO ...

I split the model into two parts that can each be printed flat on the bed. The two pieces need to be glued together inside the notch where they join. ... No supports needed.

A simple Logitech C920 webcam privacy slide cover clip. Clip it - use it = privacy. ... 2020-05-02 Add V2

I remixed the Brio webcam cover to add cutouts for the lens and microphones. The lens can be covered/uncovered for privacy with the hinged piece. The two parts are intended to be superglued together. I think it works well. ... Enjoy!

I remixed the Brio webcam cover to add cutouts for the lens and microphones. The lens can be covered/uncovered for privacy with the hinged piece. The two parts are intended to be superglued together.</p> <p>I think it works well. ...Enjoy!</p> <h3>Print...

Sliding privacy lense cover for the Logitech C920 webcam. Snap in the bottom first into the groove under the camera, then press the top section over. Slides easily to the right to expose the camera, and back left again and stops in the proper place...

The 3D print: - prevents dirty lens (= protective cover) - increases privacy (= protective shield) - Can be easily assembled and disassembled ========================================================== Die Webcam kann immer vorhanden sein, ohne dass...

... so props to him. It was very easy to resize. I basically just scaled it up to have the hole be 30mm in diameter and reduced the gap to 16mm. Even though this was resized for my specific model, this cover should fit most webcams that are 16mm thick!

A simple and not-too-elegant privacy cover for the Logitech Pro Magnetic Webcam. The GCode file is setup for Filamentum PLA, at 100 percent infill. ...Print time on my Prusa MK3s was 33 minutes.

... or closed. This uses a print-in-place hinge. The swinging cover was designed to fold completely flat when open and it does so nicely. ... I printed mine in Prusament Galaxy Black and it looks fantastic and the supports just popped off cleanly.

This is a remix of my previously posted print Privacy Cover for the Logitech C610 Webcam that adds an eye when the cover is open for a constant reminder that one could be being watched.

This is a remix of my previously posted print [Privacy Cover for the Logitech C610 Webcam](https://www.thingiverse.com/thing:4571629) that adds an eye when the cover is open for a constant reminder that one could be being watched.

Logitech Webcam Privacy Shutter Protects Lens Cap Hood Cover for Logitech Fits C920 & C922

...Support did push easily out of joint for me though - Logitech_Privacy_Cover_SHUTTER1.1(No Support).stl This is the shutter - No Support Needed (Doesn't hurt either) - Logitech_Privacy_Cover_PIN(No Support).stl This is the pin to join the two pieces.

# Logitech webcam privacy shutter Français plus bas Allows you to quickly hide the webcam to preserve your privacy. Very useful for home office. You never know if an admin does not take control remotely and allows himself to spy on us. This is a...

Cover for Logitech Webcam. ...Gives more privacy.

Simply slide for privacy to suit Logitech C922 webcam.