logitech webcam with stand 3d models
2840825 3d models found related to logitech webcam with stand.thingiverse
Simple stand for logitech (c270) webcam. ...The indentation of the camera mount must be reground a little
thingiverse
Stand for a C270 Logitech WebCam Print Settings Printer: Prusa i3 Rework 1.5 by EMotionTech Rafts: Doesn't Matter Supports: No Resolution: 0.15 mm Infill: 20% Notes: Designed with 123D Design
prusaprinters
So I designed this stand which the folded up base of the webcam fits into nicely and keeps it relatively stationary. Underneath, the two channels are designed to hold pens/laser pointers, which also double as ballast to keep the stand from moving...
thingiverse
So I designed this stand which the folded up base of the webcam fits into nicely and keeps it relatively stationary. Underneath, the two channels are designed to hold pens/laser pointers, which also double as ballast to keep the stand from moving...
thingiverse
Hanging mount for the logitech webcam. ...Used double sided tape to mount to my desk
thingiverse
I always hated the way my Logitech Webcam Stand was designed, It just wasn't practical for what I needed. I started seeing people using the Mic stands for the webcam and I thought what a great idea, so this piece holds the camera and fits on to the...
thingiverse
Basic stationary webcam mount for Logitech C920 camera. Three different heights: 45mm 60mm 75mm Hole diamater is 0.250in. for a 1/4-20 bolt. I recommend printing it so the face with the bolt hole is flat on the surface of your build plate.
thingiverse
The webcam simply has to be unfolded and then simply slides into the head with the rear part of the clamp. Please tell me what you think of the design, it's my first own design. Therefore I would be very happy about feedback. If you are...
thingiverse
by Cpayne3d June 24, 2019 Licensed as Creative Commons, Share Alike, Non-Commercial This project was created to hold a Logitech C270 web cam for my Octoprint server. Other printable camera mounts were either too small, or could not hold my C270...
youmagine
by Cpayne3d June 24, 2019 Licensed as Creative Commons, Share Alike, Non-Commercial This project was created to hold a Logitech C270 web cam for my Octoprint server. Other printable camera mounts were either too small, or could not hold my C270...
thingiverse
Quickmade ajistable stand for my c310 mounted on triple VESA screen mount wirh R36 column. Useful if you can't mount that ones on a screen frame correctly. ...You can use existing on that site models to add tripod mount to that stand.
thingiverse
Made a taller version for streaming/recording creality cr-10. ...Printed with Inland PLA and fit is a little tight, you may want to sand down the inside a little after it prints. ...YMMV
thingiverse
Made this for the Logitech C270, might fit the C310 also. ...I just prefer put my 3D printer cam off to the side rather than mount it to the printer. Can be printed standing up without support. Edit (11/14/18): confirmed to work on C310 also. ...
thingiverse
Just doubled-up this excellent stand for my c270 to add some stability. ... Camera fits in nice and snug and stays put.
thingiverse
... will have space as i didn't really want to rip the bracket off. Also as I had to cut away on the opposite side to the hinge i had to make way for the power lead. Just to add that this is the housing only the wall bracket is with the original make.
cults3d
... will have space as i didn't really want to rip the bracket off. Also as I had to cut away on the opposite side to the hinge i had to make way for the power lead. Just to add that this is the housing only the wall bracket is with the original make.
thingiverse
A remix of the Logitech C910 webcam mount by RobinFang and the tripod nut of Blueagle to add a tripod thread to the camera mount The original mount has a beveled base which lets it be attached to a specific tripod mount with a quick release plate. ... ...
thingiverse
This is a remix of the design posted by vornox. ...I simply needed one that could be installed with my Logitech Streamcam positioned in the middle.
thingiverse
... are blind, drill through when using a screw and nut. Be sure to properly isolate the PCB from the metal heatsink, use a piece of paper or plastic. C920 disassembly guide: https://en.ifixit.com/Anleitung/Logitech+C920+Webcam+Disassembly/115077
thingiverse
Frame clip gets tightened to frame with a zip-tie, then fasten together with an M3 bolt. If I were doing it again, I'd deepen the cutout for the plastic gripper nubbie on the camera, and maybe enlarge the back-bulge part. ... But this works for me for...
thingiverse
Remix of the Webcam Bracket by MrGibbon to fit on dodgrr's Ultimaker 2 Platform mount. Because I added a GoPro mount, it is compatible with all GoPro mounts. I use the camera to check print progress during my absence and to create time-lapse video's....
thingiverse
Simple dice-tray with webcam stand. ... The webcam is an old Logitech but good enough to provide image of the dice.
thingiverse
Monitor stand mount for the Logitech C270 webcam. ... My specific stand is the WALI Free Standing Dual monitor stand from Amazon https://www.amazon.com/gp/product/B018MU3SAS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 However, it should fit any...
cults3d
I wanted to create a simple stand to hold my webcam (a logitech c920) and I couldn't find one to suit my needs so I came up with this! ... Update: Following a suggestion - I 'upgraded' the model, it now has a small hole in the back to allow the cable to...
thingiverse
This business card reader stand lets you easily use a Logitech c920 webcam to take photos of business cards or driver's licenses or ID cards. ...You can use a client side webcam OCR page like https://www.imense.co.uk/DL.html to do OCR or PDF417 reading...
thingiverse
I needed a stand to mount my Logitech webcam to my printer so I could keep an eye on the prints. This is mounted to a Folgertech Prusa i3 2020 variant, but it can mount to any 2020 aluminum beam frame printer. It mounts to the rail with two 3mm or...
thingiverse
Mount you Logitech Pro 9000 on your Qidi X-one. ... Thanks to Matthew for permission to show the final print on his pictures.