logitech z506 replacement speaker 3d models
183093 3d models found related to logitech z506 replacement speaker.
prusaprinters
Therefore, by replacing the case, the attachment part can be freely designed to ensure strength.Objective 2Kenko REAL PRO Multi-Coated Glass REAL PRO 0.4x Super Wide Angle Clip Lens for Mobile Devices, Black (KRP-04SW) so that you can check a wide...
thingiverse
This is my custom cover replacement for the Logitech G720 Webcam. To install it, you'll need to disassemble the original webcam and carefully remove its electronics PCB board only. The new PCB is securely attached to the inside of the cover using...
prusaprinters
Confirmed as working with the Logitech K120. ...It may work with other models but not tested - it's 15mm wide. Ideally print with supports for the hinge pins.PLA is probably sufficient but PETG or greater is recommended.
thingiverse
My Logitech G433 was broken on both Pivot Points, but i can't find Spareparts for the G433 :-(. Here are my printable Spare Part's ;-) You need: - print all four Parts (two Left, two Right). ... - 8 M3x8 Screws - 8 M3 Nuts - T5 Torx...
prusaprinters
My Logitech G433 was broken on both Pivot Points, but i can't find Spareparts for the G433 :-(. Here are my printable Spare Part's ;-) You need: print all four Parts (two Left, two Right). 8 M3x8 Screws 8 M3 Nuts T5 Torx Screwdriver small Phillips...
thingiverse
After trying the replacement ear holder screws and watching them fail as well, I was desperate for something more substantial. That's why I went on the hunt for better alternatives and lost some of the original screws in the process. To ensure that...
prusaprinters
<p>Designed for a not very precise printer with a lot of margin but it works.</p>
thingiverse
Since I was otherwise happy with the stands I decided to model this replacement part rather than requesting a refund/replacement. This part works identically to how the original part is supposed to work. It is to be placed on the top pole with the...
grabcad
DIY Multiplex BT 5.0 Speaker Case made out of a working table and an old Speaker from Logitech. Mill it with your own homemade CNC ;-) Dimensions: approx. ...D80x200Watch the Short Video:https://www.youtube.com/watch?v=eaf-NZKl0FQYou can also visit my...
grabcad
DIY Multiplex BT 5.0 Speaker Case made out of a working table and an old Speaker from Logitech. Mill it with your own homemade CNC ;-) Dimensions: approx. ...D80x200Watch the Short Video:https://www.youtube.com/watch?v=eaf-NZKl0FQYou can also visit my...
thingiverse
One of the folding legs on my K270 keyboard snapped, so I crafted these as a substitute.\nAdded a 10mm longer version for a more dramatic keyboard incline.\nI utilized PLA but ABS should work equally well.\nPrint Settings\nPrinter: \n ...
thingiverse
K330 keyboard leg. ...Printed on my Ender 3 V2 with no supports and fits perfectly.
prusaprinters
<p>Saves some weight. ...Don't do it it's useless.</p>
thingiverse
a remix of logitch keycap k270 What did i change? ... i removed te tiny lines above and under the circle in the middle to make it easier to print
pinshape
I designed this model for my Bukito 3D printer, a replacement part for a broken headphone component. It printed well with a 0.2mm layer height and automatic support from Cura. However, using 0.4mm resulted in excessive drooping, even with supports.
thingiverse
The project involved creating a replacement part for a broken piece on my headphones. I managed to achieve good results using a layer height of 0.2mm and automatically generated supports from Cura. On the other hand, a 0.4mm layer height resulted in...
thingiverse
This custom stand is crafted to perfectly fit Logitech speakers, and can also be easily adapted or enlarged to accommodate other similarly sized speakers.