logitech z906 stand 3d models
154388 3d models found related to logitech z906 stand.thingiverse
I wanted a speaker stand for my Logitech Z906 speakers, but i could not find any cheap once. So i decided to make one myself. This design uses the ADILS legs to act as a stand. I printed this att 0.2 layer height but could easily be greater to...
thingiverse
Mount for logitech z906 controller print 2 no supports needed uses m4 bolt and tnut to mount to 80/20 Added step file so you can remix!
thingiverse
This is a remote holder that can be fixed onto my desk. ...(Logitech Z906) Print Settings Printer: Dagoma Discovery 200 Rafts: Yes Supports: Yes Notes: To be printed with full support.
thingiverse
This is a mounting plate for my Logitech Z906 satellites. Due to the ball joint, the loudspeaker can be tilted by + -25 degrees. ... To fix the final position, tighten the two M5 screws.
thingiverse
Since the control unit for the Logitech Z906 boxes was always in my way, I made a holder that you can screw under the table or a shelf. ...The remote control can also be stored on the side when not in use.
thingiverse
I wanted my Logitech Z906 sound system speakers look more clear and neutral. The speaker design looked to much technical and not perfect for the living room. So i wanted a clean cover for the speakers. It fits nicely in the small gap on the side of...
thingiverse
When I bought the Logitech Z906, I really wanted to fix these speakers to my monitor. Having switched to a wall mounted ultrawide, I got kind of OCD about having nothing standing on my desk, and anyway these full range cone speakers have a way of...
thingiverse
[NL] Om de audioweergave ervaring van mijn Logitech Z906 speakers te verbeteren heb ik een set van 2 modellen gemaakt om de speakers hoger t.o.v. mijn tv te plaatsen. Ze zijn gemaakt om op een Ikea KALLAX kast te passen. De buis is een gordijnroede...
thingiverse
Wire-Combs to help create a clean aesthetic with the Z906 speaker system. ...Probably would work with other systems, likely going to add more comb options if people are interested.
cults3d
... right side, left side to be mirrored! Screw: DIN 7380 A2 M6x8 or DIN 7984 M6x8 etc. Update 2022.01.17 Added cable menegment to "Logitech Z906 added tweeter". ...https://cults3d.com/en/3d-model/home/logitech-z906-added-tweeter
thingiverse
Wandhalterung für das 5.1 System von Logitech Z906 Lautsprecher Halterung mit Verstellung des Winkels. ... Gedruckt sollte es in Layer Höhe 0.1 Infill 80% Stützen sind nicht erforderlich Die schrauben für Boxen müssen nicht notwendig...
thingiverse
So i replaced it with the newer Logitech Z906. The front speakers are mounted on top of the rails ("handson rails") of my shelf mounting points. They slide on top of them. After you slide them on the rails you can slide the speaker with the...
thingiverse
Overview ------------ Background: Because my children and big dog keep to push off the repro from their stands, I decide to create wall holder for them. It is very simple design, right now allow just one direction move, but I work on second version,...
thingiverse
After my previous Z906 speaker mounts from a long time ago, I decided to upgrade them to a sleeker version. This one prints nicer, cleaner, uses less filament, is less bulky in your face big. Only benefits! I used table legs turned upside down to...
thingiverse
Stand for inclined compensation for Logitech Z906 Speakers. ... * Light version without boarders on front and back * 15% infill should be fine.
thingiverse
Wall mount for Logitech Z906 speakers. ... Facebook page: https://m.facebook.com/story.php?story_fbid=195946021184417&id=128803144565372 Instagram: Printareprototipare3d
thingiverse
... any meaningful way, but you know). So with my design itch having been scratched, I set about designing my own. If you enjoy this design, and own the Z906 set, you may also like my [speaker holder design](https://www.thingiverse.com/thing:4802764)
thingiverse
Logitech Z906 speaker wall mount. ... including angle 0, 15, 30, 45, 60, 75
thingiverse
Customized version of http://www.thingiverse.com/thing:12632 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=12632 Instructions Using the following options: T = 2 BL...
thingiverse
Customized version of http://www.thingiverse.com/thing:209497 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=209497 Instructions Using the following options:...
thingiverse
I saw someone said they thought there was too much weight on the top screw in the original design, so I flipped the design upside down to spread the weight a bit better.
prusaprinters
<p>I would recommend printing this with the guided inserts facing the build plate and with support material on the build plate only.</p>
thingiverse
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Print Settings Printer: Da Vinci 1.0a ...