lol holder 3d models
333966 3d models found related to lol holder.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=408698 Instructions Using the following options: show_pencil = 0 text_thickness = 3.5 pencil_hole = 1 pencil_sides = 6 letterspaces = [0,59,52,50.5,52,50,50,50,50,50,50,50,50,50,50] pencil_width...
thingiverse
Designed to solve a specific problem you may or may not have. I had seven steel machinist's rules, three 6", three 12", and one x 24", that either didn't fit (24") or were constantly jumbled in the top of one of my toolboxes. So I designed this to...
cults3d
If you are a Teemo fan you can't miss the Teemo incense holder, model printed without problems in one piece in snapmaker a350 with real size supports.
thingiverse
The LOL toilet paper holder (plus toilet paper in endless supplies, or until the filament runs out). The bracket on the top is flexible enough to put a toilet paper roll in (and out). Two rolls can be placed below as stock supply. 1x toilet paper...
thingiverse
When you buy the add on cup holder for the center console, the lid doesn't like to shut properly. Some brands come with a spacer to lower the latch to compensate for the thickness of the cup holder, most do not. ...Here is a printable spacer.
cults3d
Deodorant support to be placed on the pipe. ...Possibility to adjust the distance between the wall and the pipe with a TH M8x20 screw or more depending on the environment .
thingiverse
... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=59100 Instructions Using the following options: text_size_interior = 3 ring_size = 17.32 thick = 2 ring_angle = 15 text_face = LOL ring_width = 5 text = Remember text_size_face = 6
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = LOL Font = write/orbitron.dxf stick_thickness = 3 flat_bottom = 1 font_thickness = 5 stick_width = 8 hole_radius = 3 font_size = 10
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: flat_bottom = 1 hole_radius = 2.5 font_size = 10 message = LOL Font = write/orbitron.dxf stick_width = 8 font_thickness = 3 stick_thickness = 1.5
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=56257 Instructions Using the following options: sections = 21 text_thickness = 4 length = 15 inner_radius = 28 text = LOL outer_radius = 33 nozzlediam = 0.4
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_thickness = 5 stick_width = 8 font_size = 10 stick_thickness = 3 hole_radius = 3 flat_bottom = 1 message = LOL Font = write/orbitron.dxf
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = LOL stick_width = 8 font_thickness = 5 font_size = 10 stick_thickness = 3 hole_radius = 3 Font = write/orbitron.dxf flat_bottom = 1
thingiverse
Not sure why but my cousin wanted the words LOL... So that's what I designed and printed. Now that it's printed I kinda like it. I might make a video of the print. ...It took a little longer than an hour for me to print.