longstrike cs 6 3d models

This is a beefed up Bolt-Sled for the NERF Longstrike CS-6. Got the chunk in all the right places! It endures (tested) a 12KG reataliator Spring and still catches fine. Might work out with a heavier spring, but I don't own a heavier fitting...

The Half Length Skinny Pusher and Plunger tube block to convert the Nerf Longstrike CS-6 into a Half Length, Direct Plunger Blaster. These parts are not the complete kit and will require sourcing other parts to complete the conversion, all of which...

This is a low poly Nerf Longstrike. By MeKa. ...Enjoy!

M7A3 RIOT CS (CS 1.6 Remaster)

This one is for the Recon CS-6 and replaces some of the stock parts and adds a short barrel. You'll need to dismantle your stock by removing the two pins at the connection end. You can tap these out a couple of mm with a small screwdriver or a...

1:24 scale model of an 18inch real world rim Brand: Concept One Model: CS-6

cs

CS

CS

CS

Nerf Recon CS-6 Short Barrel Barrel opened up to stop the bullet slowing with the long barrel. Light mod fits 13mm LED torch. ... Fits the Recon MkII as well.

Custom stock for Nerf Recon CS-6. The part that goes on the gun is made in 2 pieces for ease of prtinting. There are holes for a pipe to make the glued connection stronger. Also I used pipe to connect the shoulder pad and the gun adapter. (ID 22mm,...

A NERF tripod I designed, loosely based on this one: https://www.thingiverse.com/thing:2992180 Designed to be attached on a lower attachment on a NERF Longstrike CS-6, tested. Painted for a steampunk look. ... Assembly guide in progress.

Replacement gear for a nerf gun, I think it was a Longstrike, but it might fit others.

Shaft Holder replacement for the Longstrike Nerf. I have made it using ABS and print it with a prusa i3 Instructions Insert 2 M3 bolts in the rectangular holes at the base. Insert the longstrike's...

Lid of the reload handle grip of a Nerf Longstrike Gun. update: added improved version with extra support Instructions The orange one is the original which was broken. ...Measured it all whith a...

Instructions Print part Remove barrel extension Remove bolt Remove all external screws on the main gun (not the stock) Unscrew the two screws holding the spring holder (right hand end of the spring) Use printed part inside the spring holder...

Friend needed this after modding his nerf blaster and could not be found online. Designed to have thicker back plate to try and keep it from self destructing. Keep in orientation for increased strength around the back plate. Remove...

My year 11 Graphics assignment

Adapter to connect a CS Mount objective to a ZWO ASI Mini camera having a M28.5 x 0.6 thread (1,25" filter thread).

Flash suppressor for a nerf modulus longstrike

Jason-CS/Sentinel-6 includes two identical satellites, with the first launched November 21, 2020 (Sentinel-6 Michael Freilich) and the second scheduled for launch in 2025 (satellite B). Sentinel-6 Michael Freilich (formerly, Satellite A) was renamed...

If you have a modded Nerf Retaliator and want to install the leftover stock parts into an older Recon CS-6 you will need this spacer/spring guide. This spacer holds the smaller direct plunger Retaliator spring concentric with the plunger system...

KNIFE TO PLAY AIRSOFT. ...DESIGN BASED ON THE CONTER STRIKE 1.6 KNIFE.

Picatinny Rail conversion for all the rails on the Modulus Longstrike. Nerf rails will need to side stops dremmed off, the fit is tight so a rubber mallet maybe required. This means mounting hardware is required. Followed the crazy specifications...

Reverse plunger component from a nerf longstrike, slightly modified from original to be a bit easier to print (internal featured an overhang which I've replaced with a 45° incline). Dimensions were taken from original part using micrometer. Model...

Modulus Longstrike exclusive Half Length Skinny Pusher. This is not compatible with Retaliator/Prophecy Plunger tubes as the rear seal for the pusher is a larger diameter due to the Plunger tube outlet's diameter being unique to this blaster. This...

These parts are intended to replace the "DIY" components that are shown in these guides: http://southernbrisbanenerfclub.blogspot.com/2014/02/elite-longstrike-mod.html?showComment=1393030041807&m=1 https://imgur.com/a/V9vVy These guides are not by...

This is the "Urban.mdl" model file, named "Seal Team 6" in-game, from Counter-Strike 1.5. The model is posing while aiming the Mp5. My goal was to recreate the pose seen in the classic logo of the mod. ... The "Counter Strike logo from one of...

Customized version of http://www.thingiverse.com/thing:731795 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=731795 Instructions Using the following options:...