low profile case 3d models
637949 3d models found related to low profile case.thingiverse
Low profile case for the Flip32 with vertical pins. There are 2 options for the bottom. Through holes for bolting down Solid bottom for adhesive or other mounting. ...For the solid bottom use M3x8mm bolts to hold it in place.
thingiverse
Needed a low profile, no-frills case for a project I was working on and found adamwdraper's nice deisgn. I only had M2 or M3 hardware and his called for M2.5 so simply remixed to use the M2x16 hardware I had on hand. I also added the extra hole for...
prusaprinters
Needed a low profile, no-frills case for a project I was working on and found adamwdraper's nice deisgn. I only had M2 or M3 hardware and his called for M2.5 so simply remixed to use the M2x16 hardware I had on hand. ...I also added the extra hole for...
thingiverse
... have the switches installed, it is quite stable. I was planning on doing a lot more with this, but I don't have this keypad anymore, so I'm uploading the .f3d files just in case someone wants to remix this and make something a little nicer. ...
thingiverse
This is a low profile case for the Zodiark split keyboard. There are options in the files for different configurations. You can optionally add m3 heatset threaded inserts ( ...
thingiverse
Low profile 3D printed case for the Knob Goblin Macropad https://knob-goblin.com/ Uses the 10mm M2 standoffs that come with the kit. ...Has an opening on the bottom for access to the GND and RST pins for firmware flashing.
myminifactory
Low profile 3D printed case for the Knob Goblin Macropad https://knob-goblin.com/ Uses the 10mm M2 standoffs that come with the kit. ...Has an opening on the bottom for access to the GND and RST pins for firmware flashing.
thingiverse
Needed a case for my SJ4000 that was low profile. I opted to modify Marfusio's case that screws from the inside with a flat-head screw. I also enlarged the I/O / button access holes on both sides of the case. Before printing, Check the size of...
thingiverse
Low profile base mount for flip32 or flip32+. http://www.banggood.com/Naze32-Flight-Controller-With-32-bit-STM32-for-Multicopter-10Dof-p-953849.html?p=R90804949020201412E4 More stuff at http://www.plastibots.com This thing was made with Tinkercad.
thingiverse
You can find the assembly instructions here: http://www.built-to-spec.com/blog/case-for-beagle-bone-green/ If you don't have a laser cutter, you can grab one of these cases from our store here:...
cults3d
You can find the assembly instructions here: http://www.built-to-spec.com/blog/case-for-beagle-bone-green/ If you don't have a laser cutter, you can grab one of these cases from our store here:...
thingiverse
Wanted to remix original offset support for the tarantula control case by tulsaturbo. Smaller profile. Built-in filament guide keeps the filament from straying . Option of double built-in t-nut or single built-in plus real t-nut to lock. M4 nuts...
thingiverse
This is my attempt on a case for the Sofle Choc v2 keyboard by Josef Adamcik/Brian Low. I use the v2.2 Version from 42. keebs with an added power switch, but it should really work on any v2 revision. I tried to keep the case as flat as possible. It...
thingiverse
Simple case for the "Atomic Pi" single board computer. Because of the official model totally doesn't fit with the stupidly placed bottom power connector, i created this one. You may add bevels and extra holes for electrical access to GPIOs etc....
thingiverse
This is a low profile case for the 6 Port RGB Scart Switch from [Otaku Games](otaku-games.com), sacrifying the secondary RCA output for decreased height requirements, not interfering with bigger SCART plugs. It's easy to print and provides efficient...
prusaprinters
This is a low profile case for the 6 Port RGB Scart Switch from Otaku Games, sacrificing the secondary RCA output for decreased height requirements, not interfering with bigger SCART plugs. ...It's easy to print and provides efficient dust...
thingiverse
The second part is a low profile bottom case for the VOID40 handwired keyboard, there should be enough space for the arduino and the wiring. All screw sizes, hole dimensions and tolerances remain the same as the original. It is compatible with the...
thingiverse
This case is low profile and also features multiple sets of holes on the bottom surface to allow Zip ties to be threaded through for easy mounting (I recommend putting the zip ties in before installing the Pi). Also, this case allows the Pi to be...
prusaprinters
This case is low profile and also features multiple sets of holes on the bottom surface to allow Zip ties to be threaded through for easy mounting (I recommend putting the zip ties in before installing the Pi). Also, this case allows the Pi to be...
thingiverse
Tip: If the camera wobbles inside the case, gently wedge some foam or similar behind the camera before closing the case (pieces of heat-shrink shown). Tip: When making/choosing a printing profile, opt for something that will give you strong layer...
thingiverse
This is a tenting case for the Avalanche v4 (https://github.com/vlkv/avalanche). To add the tenting legs you will need to use M3 heat set threaded inserts and M3 screws. UPDATE: I added a 60% version with no pinky and no tenting for those who...
thingiverse
I love this case for the Atomic PI but I needed to add some mounting to affix it to the print farm enclosure I'm building. I also felt it needed some venting on the top half side to allow a fan to be mounted to the heatsink. I don't think this...
thingiverse
I found that for the Pi Zero W that I have, the heatsink cutout was in the wrong place, so this is a remix to move it to the right position. I've only included the top part, you'll need to print one of the bottom parts from the original source. ...
thingiverse
This should be pretty straightforward to print on really any settings. ...The screw mounts are made for M2 heat-set inserts like these: https://www.mcmaster.com/94459A110
thingiverse
I used heatset inserts M2x3 and screws M2x4 to mount the Nyquist PCBs.
thingiverse
ender 3 pro octopi w/ ice low profile cooler case
prusaprinters
A low profile case for the Agon Light. ...Requires four 3 x 20mm nuts and bolts for the corners and optional - four self adhesive rubber feet (~10mm diameter) Use 2 - 2.5mm diameter screws to secure the pcb to the case.I printed my case with transparent...
thingiverse
Slim case for MSI GTX 750 TI to fit in small / slim pc cases I think it ok for msi gtx 1050 2gb version also