lrp blast 3d models

This is a reproduction of the gear dust cover for the LRP S10 Blast Models.

This is a reproduction of the gear dust cover for the LRP S10 Blast Models. ...Tested and fits.

This is the central plate of an LRP Blast S10 TC remote control car. ... Print Settings Printer: Geeetech Prusa I3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 100%

As the LRP Blast Canopy is slightly bigger compared to the original Quanum Vandal canopy, I had to lift it up a few millimeter with these adapters. Print flat on the side for strength. ... Should also fit on : VRX Spirit FTX Vantage INTEGY i10B...

Print Settings for the LRP Blast S10 TC RC Car Battery Pin Height: 33mm Diameter: 6.5mm Printing Details Printer: Geeetech Prusa I3 Supports and Rafts Rafts: Yes Supports: No Layer Resolution Resolution: 0.1mm Infill Density Infill: 100% Notes for...

Purchased a LRP Blast 2 Canopy and Wing from ebay and adapted both to my Quanum Vandal. Mount Holes from the Blast Wing are wider compared to the Vandal. Blast Wing is also thinner, so cut off a few Millimeter from the mounting Pin. Print horizontal...

Spoilerhalter für den LRP S10 Blast 2

This is a custom-made front shock guard that I designed for my ZD Racing Thunder sc-10, but it will fit perfectly on the LRP-s10 Blast 2 since both trucks share the same chassis and shocks. It may also work with other ZD Racing and LRP cars that have...

The axle legs for the S10 Blast from LRP are both right and left sides.

Mittleres Topdeck LRP S10 Blast 2

Modified SpeedDragon77 file to fit my LRP S10 blast. ... Allows you to put bodies with a high rear

I designed it for my 1/10 RC buggy LRP S10 Blast BX, because original part is very soft and it's easy to break it. I hope, that this one will be better and I will save time for another RC racers with designing. It is designed for using Hex socket cap...

Vorderes Topdeck für den S10 Blast 2

Front-line support pillar before depreciation for Large Retailer Plan S10 blast

Maybe suitable also for EZ racing Thunder 1/10 rc touring car

Parts: Cushioning bracket. Front body support. Rear body support. Magnet support. Magnet holder expander. Upper foam support. Foam. Lower foam support. Foam hexagon turret. Front piece shaft clamp. Rear axle clamping piece. Pieces: Damping...

I destroyed my fender, and now I'm forced to build a new one. ...Unfortunately, the replacement part supply at LRP isn't working out too well for me.

Die Ersatzteilversorgung bei LRP klappt leider nicht sooooo gut. Here is the machine translated description. Since I destroyed my fender, I had to construct a new one. ...The spare parts supply at LRP does not work sooooo well. Print...

Bigger receiverbox cover for S10 Blast MT2. ... Fits even for an old 40MHz receiver.

LRP S10 BLAST BX with chocolate and shock absorption coating Shock absorption coating: Polyflex PLA by Polymaker - Temperature: 222° - Speed: 40mm/S - Wall thickness: 1.2mm - Infill percentage: 10% - Layer height: 200µ Porotége Amoertisseur: Polyflex...

A designed cover is placed between a LRP S10 Blast RC car's chassis and top deck, covering the slipper axle and rear driveshaft bearing. The small slot at the front allows the driveshaft to pass through while preventing dirt and rocks from reaching...

Steering Knuckle === Description -- This is a replacement part for the LRP S10 Blast Steering Knuckle left and right. It broke after crash, so I redesigned it in Fusion 360 to make it a bit stronger. I have also included the Fusion 360 File for...

Der Batteriehalter ist auch für Akku´s mit seperaten Balancerkabel geeignet.

Humans can reposition the holes based on print quality, resolution at 150µ, filling at 100%, printing speed around 40mm/s, and estimated print time of about 22 minutes. If you have any questions, ask me in the comments or at...

<p>Als Ergänzung zum normal großen Heckspoiler habe ich hier noch eine verkleinerte Variante. Hoffentlich werde ich den dann nicht so oft ersetzen müssen.....</p> <p>Here is the machine translated description.</p> <p>As a supplement to the normal...

Front Suspension Arm === Description -- This is a replacement part for the LRP S10 Blast Front Suspension Arm. It broke after crash, so I redesigned it in Fusion 360 to make it a bit stronger. I have also included the Fusion 360 File for further...

A simple upper chassis part with bearing holder, if you broke yours on your car and don't have spare part at home.

I crafted this as a gift for my buddy and plan to snap some photos once we give it a test run together.

A simple upper chassis part with bearing holder, if you broke yours on your car and don't have spare part at home.

Hello, I created this tutorial because the original button was broken and I took advantage of it to move it outside of the body for easier access. Here's the button I used: http://www.ebay.com/itm/5-x-...