lrs printing 3d models
1201184 3d models found related to lrs printing.thingiverse
This is a Mod for the Antena on the wolfbox LRS system. ... Print in pla
thingiverse
Terminal cover for MeanWell LRS-75 power supply. ...This one actually fits the LRS-75. Print it as in the .stl, the small overhang doesn't need support.
thingiverse
It should be compatible with all the LRS-75 series: LRS-75-5, LRS-75-12, LRS-75-15, LRS-75-24, LRS-75-36, LRS-75-48 When printing the lid, you must pause the print twice to insert 3 nuts. ### Assembly: * C14 * 2 x M3x4 for the back of the PSU ...
thingiverse
This is enclosure for LRS i developed. ...Finf out more on project site.http://qczek.beyondrc.com/qczek-lrs-433mhz-1w-lora-rc-link/
prusaprinters
... accessory with no needs for fasteners to the actual power supply. I’m prepared for this to a hurdle in terms of getting the clearances just right. I envision a few self tappers in my future.More info:https://dewz.pro/2022/09/20/lrs-200-power-sleeve/
thingiverse
Holder for MeanWell LRS-50-12 2x M3x30 or M3x35 + Nut M3 for cover 2x M3x8 or M3x10 + Nut M3 for LRS-50-12 4x M3x8 + T-NUT M3 Designed for https://www.thingiverse.com/thing:3347604
grabcad
LRS.F 09 is prototype Carrier Vessel class super carier, this design my inspiration from USS NIMITZ
prusaprinters
This is enclosure for LRS i developed. ...Finf out more on project site. http://qczek.beyondrc.com/qczek-lrs-433mhz-1w-lora-rc-link/ Category: R/C Vehicles
thingiverse
After seeing Nero use a LRS 24v power supply to run his TS100 soldering iron, I knew I wanted to the same setup in order to have one power supply that could run my soldering iron and fume extractor. Since it would utilize XT60 receptacles, I could...
prusaprinters
DIN rail mount for MeanWell LRS-35 series power supplies. ...This aligns the bottom of the supply with my other LRS mounts. I have included STEP and FreeCAD sources if you want to modify.
thingiverse
A simple cover for the Mean Well LRS-100 power supply. ...Two screw holes for mounting to the PSU, a hole for the AC cord, and a hole for the DC output.
thingiverse
IEC320 C14 Inlet Module Connector Male Power Socket w Switch AC 10A 250V: https://www.amazon.com/gp/product/B078PJ66G6 The LRS-100 is attached to the case with two countersunk M3 screws. ... Not shown in the picture, but fits a 5.5mm x 2.1mm DC Power...
prusaprinters
Cover for a MeanWell LRS series power supply, designed to prevent access to the terminals with a cutout for an integrated IEC plug, switch and fuse. It has four holes for input and output cables.</p><p>The cutout for AC power is 48mm x 27.5mm with...
prusaprinters
... <p>The wireing is easy, but if you dont know for sure how to do it - ask an electrician. Mains power can kill you. Print Settings Rafts: Doesn't Matter Supports: NoResolution: 0.2 Filament: add:north Economy white Category: Electronics
thingiverse
Back lid of the orange open lrs transmitter that fits JR and Turnigy radios. Will angle the antenna and avoid that the controller rest on antenna when it lies down. ...The antenna cable used is the one included when you bought the module.
thingiverse
This bracket can be used to mount Meanwell LRS 35 series power supplies to V-Slot 2020 extrusions as used in many 3D printers or hobby grade CNC machines. Steps: 1: M5x10mm bolt (x2) and M5 hammer nut (x2) to mount bracket to V-Slot 2: Use M3...
thingiverse
This is a cover for a Meanwell LRS-350 PSU (power supply unit). The base is big enough that it is fairly stable standing upright, or it can be used laying flat. I use a right-angle power cord when I'm using it laying flat. ...I included a STEP file to...
thingiverse
Hinged cover with fused outputs utilizing XT60 connectors for a Meanwell LRS PSU. Most likely will work for other low profile Meanwell PSUs also. This is a remix from https://www.thingiverse.com/thing:3450424 I made both the top and bottom...
thingiverse
Cover for a MeanWell LRS series power supply, designed to prevent access to the terminals with a cutout for an integrated IEC plug, switch and fuse. It has four holes for input and output cables. The cutout for AC power is 48mm x 27.5mm with 1.5mm...
prusaprinters
Designed to cover the wiring connections on a Mean Well LRS-350-24 power supply and provide a mounting location for an IEC320 inlet socket.Specifically designed for this power connector:...
cults3d
:) https://paypal.me/jpal85 Threw together a quick remake of my previous lrs-150 psu enclosure. This one uses a thinner/smaller C14-switch and my new xt60-clamps. The cover is press fit and has 1-2 screw holes as well. Uses this C14-switch (no fuse...
thingiverse
:) https://paypal.me/jpal85 Threw together a quick remake of my previous lrs-150 psu enclosure. This one uses a thinner/smaller C14-switch and my new xt60-clamps. The cover is press fit and has 1-2 screw holes as well. Uses this C14-switch (no...
cults3d
Easy to print. It is an antenna mount for Turnigy radios using Long Range Radio system. Attached with zip ties. ... It is sized for an antenna with a 11 mm base.