lt1 v8 3d models
3644 3d models found related to lt1 v8.
cgtrader
Corvette 6.2L V8 Engine - 3d Engine Model, The high detail exterior is great for close up renders, Also the model was created with 3DS Max 2008 using the open subdivision modifier which has been left in the stack to adjust the level of detail.
thingiverse
Water pump seals on the LT1 V8 engine are extremely difficult to install correctly without the J39089 tool. I was without one, but I had a few minutes so I whipped my own version up in solidworks. My first version fit a little snug, so this v2 is...
cults3d
A model of a light tank, created by me according to the rules of BT. Scale for 6mm. Divided for convenient and easy printing (includes a connoisseur undercarriage). There are 2 versions available. Ballistic and energetic. Floats. The turret and case...
grabcad
Found some pretty awesome drawings by this guy, "Jan Elg", for a V12 Merlin engine. ...From those i laid the foundation for my own V8-project.
thingiverse
Reflector for the Sofirn BLF LT1 lantern. ...I used duct tape for the reflective surface.
thingiverse
A simple base for the BLF/Sofirn LT1 lantern. ...The cutout in the bottom is for a ring of rubber or foam.
thingiverse
BLF LT1 lantern as a reference for you mods and accessories. ...Outside dimensions are as accurate as I could measure them.
thingiverse
... even more. Credits to Big_Sam for the original idea and first prototype. I've modeled this based on his photos and my [LT1 reference model](https://www.thingiverse.com/thing:4714912) and simplified it for easier printing and more robustness.
thingiverse
This is the shade I designed for the BLF LT1 Lantern. I print it in PETG at 0.16mm on my Ender 3 v2 I print with a RAFT for best success. ...
prusaprinters
A simple base for the BLF/Sofirn LT1 lantern. There are two versions: v2: Wider, thicker version. The cutout in the bottom is for a ring of rubber or foam.</p> <p>v3: Slightly smaller and more minimal version. ...It is as wide as the head of the LT1 so...
thingiverse
This is a simple base for the Sofirn LT1 lantern. It expands the base to approximately 4 inches to help reduce tipping. You'll need a 1/4x20 screw (1/2 inch long) and a hex nut. Inset the hex nut from above, tighten the screw from below, and then...
prusaprinters
The LT1 Mini lantern is a little top heavy, so i wanted a base to stop it from tipping over. The print pictured is in TPU, but i printed one in PLA as well, and it works just as well. ...I used 5% infill, but I'm sure 0% would also work...
thingiverse
A simple base for the BLF LT1 LED Lantern - a community-produced LED lantern of epic proportions. Come check it out here! http://budgetlightforum.com/node/44923 This base is held on by friction, I printed this on my MP Select Mini V2 and it fits...
thingiverse
This is a simple shade for the Sofirn LT1 lantern. Honestly, there are nicer looking options out there, but I already designed this, so here it is. It's completely flat on the bottom, so no supports needed. It has an inner diameter of 35.65 mm. ...
thingiverse
A simple lamp shade for the BLF/Sofirn LT1 lantern. There are two versions available: v1: My original idea, but my printer struggled with the 60° overhang at 0.2 mm layer height. v2: Slightly different design with a maximum overhang of 50°...
cults3d
Stingray LT1 Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing.