lucy from elfen lied 3d models
727626 3d models found related to lucy from elfen lied.thingiverse
Long time ago I created an Elfen Lied 3D statue, but I was unable to print it in resin or whatever (very expensive, you know...) so I abandoned the idea. But today I was thinking about something to print, in order to finish a very bad quality...
thingiverse
Keychain styled after the anti diclonius helmet from Elfen Lied
thingiverse
Customized version of http://www.thingiverse.com/thing:813330 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: 4swidth...
thingiverse
My wife loves the show so I'm trying to make a wearable version for her. ... I tried to cut them small enough to fit on smaller printers.
thingiverse
Customized version of http://www.thingiverse.com/thing:53235 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: ...
cults3d
Join Our Patreon for 12$ this month and you can get 2 models of this month and 6 Models from Welcome pack. ... FunserviceSTL ...
sketchfab
- Lucy always cares about those around her, this can not be taken away from her, not for nothing did her mother send her to medical College. ...More artworks on my Artstation: https://www.artstation.com/dzrobo
sketchfab
The Lucy model was created for the short film Lucy’s Room as part of student project.
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264478 Instructions Using the following options: radius = 40 wall_thickness = 2 font_density = 1.7 bottom_height = 4 bottom_factor = 0.825 text = LUCY LUCY LUCY LUCY LUCY LUCY height = 100
thingiverse
... can, with Lucy! Instructions print on long side, with "LUCY" side up. extra material will be on both sides of hole. remove extra material on one side and use the extra material on other side as a floor for the cig. ...btw, smokings bad mmmkay.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=409217 Instructions Using the following options: name = lucy font_name = orbitron.dxf height = 35 volume = .375 wall_thickness = 5
prusaprinters
Lucy is 149 mm long x 65 mm high x 20 mm deep. ... It is made with SketchUp 2015 using the Arial Bold font.</p> <h3>Print instructions</h3><p>10% fill</p>
thingiverse
Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockWidth = 2 BlockLength = 4 Name = LUCY
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=409217 Instructions Using the following options: name = lucy font_name = orbitron.dxf height = 35 volume = .375 wall_thickness = 5
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=409217 Instructions Using the following options: volume = .375 wall_thickness = 5 font_name = orbitron.dxf height = 35 name = lucy
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: flat_bottom = 2 stick_width = 8 stick_thickness = 3 hole_radius = 3 Font = write/orbitron.dxf message = LUCY font_thickness = 5 font_size = 10
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: Font = write/Letters.dxf stick_width = 8 font_thickness = 5 hole_radius = 3 stick_thickness = 3 flat_bottom = 1 message = Lucy Hu font_size = 10
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: textstring = Lucy basethickness_percent = 0.1 fontname = Holtwood One SC baseheight_percent = .33 shift_font_percent = 0.07 do_shift_font = no...
thingiverse
... http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options: Text_Size = 10 Your_Text = LUCY Text_Rotate = 0 Text_Font = write/knewave.dxf
thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=1955876 Instructions Using the following options: ring_offset = 1.5 letter_font = Fontdiner Swanky ring_diameter = 3 letter_spacing = 0.92 ring_thickness = 1.2 name = Lucy keychain_thickness = 4
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 10 Font = write/Letters.dxf hole_radius = 3 stick_width = 8 stick_thickness = 3 message = Lucy flat_bottom = 1 font_thickness = 5
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=408698 Instructions Using the following options: pencil_width = 14 show_pencil = 0 pencil_sides = 6 text_thickness = 3.5 pencil_hole = 1 pencil_color = green text = Lucy letterspaces =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1148986 Instructions Using the following options: letter_3_height = 4 Rotation = 50 twist = -5 Loop_x_position = 10 letter_6_space = 10 letter_1_height = 6 letter_6_height = 5 Loop_y_position =...