lumenier 3d models
654 3d models found related to lumenier.grabcad
Lux Lumenier flight controler board for racing drones.Elements used from GrabCad:LQFP-64passive SMDSOT23 PackageMicro USB-B Female 5Pin SMDPackage SMABL-LS0805UWCSMD Miniature Tactile Switch 3x6x2.5mmCD43
thingiverse
This is a turtle mode fin for the Lumenier Chief racing frame.
cults3d
You can use this dummy to construct your own Case for a Lumenier Micro AXII.
grabcad
Lumenier QAV-X Charpu (3mm carbon frame)Frame for RC racing.Solidworks 2015, ACIS & Parasolid.
grabcad
More info about this motor can be found here https://www.getfpv.com/lumenier-rx2204-14-2300kv.html
thingiverse
Claw for Lumenier QAV-R2. 25.21 g with the 9g servo. ... The quad has 50 mm landing gear.
grabcad
More info about this motor can be found here https://www.getfpv.com/lumenier-rx2206-11-2350kv-motor.html
grabcad
A model of this antenna: https://www.getfpv.com/lumenier-axii-u-fl-5-8ghz-antenna-rhcp.htmlThe coax and U.FL connector are not included.
thingiverse
This is a frame protector for Lumenier qav-cine freybott edition 2.5" drone. Print 8 of them with TPU then install with the screws. ...
thingiverse
Simple bumper which fits a Lumenier QAV250 G10 frame perfectly. Use a drop of hot glue or double sided tape to secure it into place. ...It fits the front as well as the rear of the frame.
thingiverse
A simply design to protect the lumenier 600mw vtx antenna, its designed to use it with a right handed sma connector. ...Fits securely, no glue or double sided tape needed.
thingiverse
We organize and pratice FPV racing in France with my team AMR (http://www.amr-asso.com) and we use TX5G25 from Lumenier proudly gived by our partner StudioSport (http://www.studiosport.fr/emetteur-lumenier-mini-25mw-5.8ghz-32ch-raceband-a9412.html).
thingiverse
Protective case for Lumenier video transmitters TX5G*R series. My main goal was to properly secure the Fatshark CP antenna, it is unlikely that this would work with the stock antenna. Make sure you tie a ziptie around the antenna as tight as you...
thingiverse
This is a replacement cap for your Lumenier AXII Antennas, I was flying today and had a little crash with my LittleTad-EX, I lost the antenna cap and wasn't able to find it... Thank God I have a 3D printer :)) I came home and took some measurement...
thingiverse
I needed a replacement arm for my Lumenier Chief frame so I made one. This model isn't literally perfect but it's pretty close and slots right in effortlessly. I added a .4mm or so chamfer to one side to counter elephants foot just a tad. ...
thingiverse
Combined Motorguard and Landingskid for the Lumenier QAV250
grabcad
More info about this motor can be found here https://www.getfpv.com/lumenier-mb2206-9-2450kv-freybott-motor.html
thingiverse
This model was designed using OpenSCAD, taking measurements from a physical Lumenier AXII 2 antenna. Can be used to model your own mounts. ... Hope this helps.
thingiverse
This is a dipole mount for the front of the Lumenier QAV-S frame. This works for the original, NOT JB, Johnny FPV, etc. ...
thingiverse
Plug-and-play motor protector for a Lumenier QAV250 G10 frame. Easy to mount without any bolts or glue. Perfect fit for the Lumenier FXC2206-11 motors. ...Post-Printing After printing you might need to cut off a small portion the snap-on mechanism so it...
cults3d
Arm guard + skid designed for the lumenier QAV-S (original) frame. ...Print it with around 20% infill in order to make it lighter and so that it will better absorb shocks.
thingiverse
... And remember to keep up to date at https://www.facebook.com/framefpv/ Link to the battery (which I HIGHLY recommend for 3" quads) https://www.getfpv.com/lumenier-850mah-4s-75c-lipo-battery-xt-30.html Also fits the new Lumenier N2O 120C version.
thingiverse
Mounting for the lumenier micro axii ufl version on the seeker underbone. ... I put a bit of hot glue in the hole before pushing the supporting plastic for the axii down the hole, this secures it during flight
thingiverse
Prop guard for Lumenier QAV-S quadcopter. Suitable for printing with rigid filaments like PETG, ASA, PLA, etc. Protects props from light impacts if you're flying cine-style. ... Not suitable for bando/freestyle.
thingiverse
I had a heavy crash with my Japalura and split the cover on the Lumenier AXII Stubby 5.8GHz Antenna. ... So I 3d printed a replacement as the internals were not damaged.
thingiverse
Designed this LED mount which sits under the bottom plate at the back on the Lumenier Qav R. I printed with Pla, 0.20mm and 80%infill. ...If the mounting hole too small just use a 3.5mm drill.