lumenier led 3d models
73730 3d models found related to lumenier led.thingiverse
Front and rear LED holder for the 2.5cm 6 LED strips from this seller on eBay - http://www.ebay.co.uk/itm/SCALEXTRIC-SCENERY-12V-LED-STRIP-LIGHTS-QUAD-DENSITY-BLACK-BACKING-BRIGHT-/181562215289?var=&hash=item2a45f38b79:m:mKiv1hG_99PlxRKEJ6borjw...
thingiverse
Simple isolation plate for Lumenier RGB LED boards for mounting on 4mm+ wide quadcopter arms. SLA version edges came out a bit cleaner. PLA version seems to fit a bit more snug. ...
thingiverse
Designed this LED mount which sits under the bottom plate at the back on the Lumenier Qav R. I printed with Pla, 0.20mm and 80%infill. ...If the mounting hole too small just use a 3.5mm drill.
thingiverse
This is a LaForge LED Holder. ... I used ABS and it has a snug tight fit, I tried 2 LEDs. ...This fits the QAV-X perfectly.
thingiverse
Portaleds para canopy de lumenier. ...preparado para leds diatone. Leds diatone ---- https://goo.gl/7Wx3YX
thingiverse
Hi all. ...This design for Realacc X210 frame https://goo.gl/LiZcr8. I made some mount for COB LED like this https://goo.gl/gDvtuL
thingiverse
Using the original standoffs for the Realacc X210 frame, I measured out this LED mount. It has the cut shaped into it for the carbon fibre that sits behind the front standoffs. It's 7.5mm high and 50mm wide. Curved to make it look nicer. Will try to...
grabcad
Lux Lumenier flight controler board for racing drones.Elements used from GrabCad:LQFP-64passive SMDSOT23 PackageMicro USB-B Female 5Pin SMDPackage SMABL-LS0805UWCSMD Miniature Tactile Switch 3x6x2.5mmCD43
grabcad
Lumenier QAV-X Charpu (3mm carbon frame)Frame for RC racing.Solidworks 2015, ACIS & Parasolid.
cults3d
You can use this dummy to construct your own Case for a Lumenier Micro AXII.
thingiverse
This is a turtle mode fin for the Lumenier Chief racing frame.
grabcad
More info about this motor can be found here https://www.getfpv.com/lumenier-rx2204-14-2300kv.html
thingiverse
Claw for Lumenier QAV-R2. 25.21 g with the 9g servo. ... The quad has 50 mm landing gear.
grabcad
More info about this motor can be found here https://www.getfpv.com/lumenier-rx2206-11-2350kv-motor.html
thingiverse
This is a frame protector for Lumenier qav-cine freybott edition 2.5" drone. Print 8 of them with TPU then install with the screws. ...
grabcad
A model of this antenna: https://www.getfpv.com/lumenier-axii-u-fl-5-8ghz-antenna-rhcp.htmlThe coax and U.FL connector are not included.
thingiverse
A simply design to protect the lumenier 600mw vtx antenna, its designed to use it with a right handed sma connector. ...Fits securely, no glue or double sided tape needed.
thingiverse
Simple bumper which fits a Lumenier QAV250 G10 frame perfectly. Use a drop of hot glue or double sided tape to secure it into place. ...It fits the front as well as the rear of the frame.
thingiverse
We organize and pratice FPV racing in France with my team AMR (http://www.amr-asso.com) and we use TX5G25 from Lumenier proudly gived by our partner StudioSport (http://www.studiosport.fr/emetteur-lumenier-mini-25mw-5.8ghz-32ch-raceband-a9412.html).
thingiverse
Protective case for Lumenier video transmitters TX5G*R series. My main goal was to properly secure the Fatshark CP antenna, it is unlikely that this would work with the stock antenna. Make sure you tie a ziptie around the antenna as tight as you...
thingiverse
This is a replacement cap for your Lumenier AXII Antennas, I was flying today and had a little crash with my LittleTad-EX, I lost the antenna cap and wasn't able to find it... Thank God I have a 3D printer :)) I came home and took some measurement...
thingiverse
I needed a replacement arm for my Lumenier Chief frame so I made one. This model isn't literally perfect but it's pretty close and slots right in effortlessly. I added a .4mm or so chamfer to one side to counter elephants foot just a tad. ...
thingiverse
Combined Motorguard and Landingskid for the Lumenier QAV250
grabcad
More info about this motor can be found here https://www.getfpv.com/lumenier-mb2206-9-2450kv-freybott-motor.html
thingiverse
This is a dipole mount for the front of the Lumenier QAV-S frame. This works for the original, NOT JB, Johnny FPV, etc. ...
thingiverse
This model was designed using OpenSCAD, taking measurements from a physical Lumenier AXII 2 antenna. Can be used to model your own mounts. ... Hope this helps.
thingiverse
Plug-and-play motor protector for a Lumenier QAV250 G10 frame. Easy to mount without any bolts or glue. Perfect fit for the Lumenier FXC2206-11 motors. ...Post-Printing After printing you might need to cut off a small portion the snap-on mechanism so it...