lumenier 3d models

Mounted the VTX inside my TRX4 to enable FPV crawling and it was a huge success, working flawlessly. ...In addition, I crafted an AXII stubby antenna holder to complete the setup.

I designed a GoPro Hero mount for a LumeMier QAV R2 frame, specifically for a friend. Multiple angles and a version for the GoPro Session will be added soon. ... GoPro Hero: - 25 degrees - 35 degrees - 45 degrees (optional) GoPro Session: - 25 degrees...

Mount Luminier 180 camera to the Fat Shark 600 TVL system. ... Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: No Resolution: 0.25 Infill: 10%

This design accommodates the diminutive Nano-520TVL camera produced by Luminier with precision. ...I trust you will discover it advantageous.

This is the base for the servo tilt gimbal, you will also need the Universal Mount: https://www.thingiverse.com/thing:5135106NOTE: "TabSlot" Base must be used with "TabSlot" Universal MountGuide for 3D printing the gimbal design here:...

Using original standoffs for Realacc X210 frame, I measured out this LED mount carefully. It has a cutout shaped into it for carbon fibre that sits behind front standoffs precisely. Measuring 7.5mm high and 50mm wide, it's curved to give it a nicer...

Hello everyone. I've created a custom design for the Realacc X210 frame located at goo.gl/LiZcr8. ...Additionally, I've developed mounts specifically for COB LEDs, which can be viewed at goo.gl/gDvtuL.

Replaced 50-degree mounting plate from an Runcam Swift, awaiting testing to confirm functionality.

The print must be made using TPU or similar flexible filament. It perfectly fits the GoPro Session and the Polaroid Cube. When printing, place it on its side with support structures. ...This design has been confirmed to work with both the QAV-R and the...

A custom mount is designed specifically for the Axii 2 antenna, featuring extended arms that allow for greater separation between the antenna and its frame. This deliberate design choice aims to enhance reception quality by reducing interference from...

The mount is as minimal and lightweight as possible while making a very solid adapter to the GepRC Mount. It enables a downtilt of approx. 12° for vertical filming or slight downward filming while flying slowly. ...I printed it in PETG, other Materials...

This mount is specifically designed to integrate into the frame and weigh almost nothing in order to have a neat setup. After printing you may need to widen the hole for the Polar Antenna a tiny bit, depending on your print quality. The connector...

printed in nylontpu without support if you like this give me a sub on IG or YT https://www.instagram.com/martymcfly_fpv https://www.youtube.com/channel/UC0Ps_VxWIuz_74Qz01wQ68w

Since the Naked Hero-Designs goes in all direction (GepRC, Naked6, etc.) I bought one from our local dealer fpvframe.ch. The Naked8 doesn't fit in the BetaFPV-GoPro-mount so I had to design it for myself. After 6 failing attempt, I came up with this....

other side has to be mirrored in slicer for clean nanoRX installation i recommend this print https://www.thingiverse.com/thing:4731250 if you like this give me a sub on IG or YT https://www.instagram.com/martymcfly_fpv ...

Holder for the GEPRC Naked GoPro Hero 8

Needed an adapter for my brand new Caddx Air Unit to fit the QAV-S Johnny FPV Edition. This adapter will fit for the new micro camera from Caddx Air Unit 19mm to the 21mm cage of the Luminier QAV-S JonnyFPV frame. ... Print in tpu

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

remix

I made this holder to prevent the antenna from ending up in the props

Remix von https://www.thingiverse.com/thing:4603848 Auf der Unterseite einen 10º Winkel/Kante eingefügt. Dadurch lässt sich der Mount leichter befestigen Auf der Oberseite ist die SD-Karte nun zugängliche ohne die GoPro zu entfernen. ... ...

I remixed the original tbs predator camera mount to fit my qav-r 2. I printed in priline tpu to test it and so far so good. I really like this camera mount on my TBS Source One V3 so I figured why not adapt it over. Full credit for this design goes...

Just my redesign of a Insta360 Go camera mount for the QAV-Cine 2.5" freybott edition..

hero 8 mount remixed for the QAV S

This is a remix of MacNeill's design of the antenna holder. It has been remixed to fit the QAV-S mini. ...Used the Happymodel EP1 TCXO receiver, available here: AliExpress: https://s.click.aliexpress.com/e/_DEHU74j GetFPV: http://bit.ly/3GRtYC8

Remix of GrowingSurvival's design to make it fit a QAV-S Mini. ...Note that the Immortal T angles downwards to give more clearance from props.