m10 fine thread 3d models

My Vitpilen 401 utilizes both right-hand and left-hand threads, making both STLs available for printing. Easy to print without supports required. A universal version without logos (Thing 3969030) has also been modeled. ...If you're interested in a...

http://www.thingiverse.com/apps/customizer/run?thing_id=45117 Instructions Using the Following Options: Chamfer_Size = 1 Rosette_Radius = 6 Rosette_Offset = 3 Wall_Thickness = 3 Knob_Diameter = 60 Knob_Type = 2 Knob_Thickness = 15 Number_of_Rosettes...

... item #311919 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=311919 Instructions Using the following settings: Down - 1 Type - 1 Space - 17 Thread - 10 Length - 20 Wrench Sizes - 0 $fn - 60 Accuracy - High

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=311919 Instructions Using the following options: $fn = 30 Thread = 10 Type = 1 Length = 25 Down = 1 Accros = 1 Space = 17 WrenchSizes = 0

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=311919 Instructions Using the following options: WrenchSizes = 0 Space = 17 Thread = 10 Accros = 1 $fn = 30 Down = 1 Type = 0 Length = 25

......To create this specific design, the following options were used: Wall Thickness of 5, Rosette Offset of 4, Knob Fill of 1, 6 Rosettes with a Radius of 7, Knob Diameter of 45, Knob Thickness of 15, Thread Size of 8, Knob Type 2, and Chamfer Size of 2.

ACME thread

Thread protector

Bilateral Thread

buttress thread

Thread Mill

Thread_5

thread rack

knuckle thread

THREAD PARTS

Stair thread

thread rack

... Size adds a smooth edge to all corners. Knob Type number 3 is chosen for customization. Each Rosette has a Radius of 6 units. 2 units fill the Knob interior with solid material. Thread Size is set to 8 units. ...The Knob Thickness is 15 units.

I printed it in PLA and wrapped some teflon thread tape and screwed it into the compressor. The compressor gets warm and softened the PLA print. I had to support the air hose so it did not put a force on this fitting when it was warm, used it for...

Needed a connector for 8mm silicone tubing to an M10 threaded wire

A simple holder for M10 and M12 horse struds with a threaded box for grease

Simple filament spool adpter for M10 threaded rod to 54mm diameter. ... (Designed for my XViCo X1)

A vital connection is required for attaching 8mm silicone tubing to a threaded M10 wire.

To ensure a secure fit, I wrapped some teflon thread tape around it before screwing it into place. As the compressor operates, it can become warm, causing the PLA print to soften slightly. In order to mitigate this issue, I took the precaution of...

To get it fast, I designed and printed this in PLA plastic and wrapped some teflon thread tape around it before screwing it into the compressor. After just a few uses, the compressor started to heat up and soften the PLA print. To prevent damage...

Possibile inizio e fine del fiume....

Fine filament detector support for Sidewinder X1

DIY diorama This is fine for printing

This is fine. ... The CLASSIC MEME!

The perpendicular threads are layered on top of each other with a small gap for accurate detection as lines during slicing. This enhances the appearance and strength of the printed object. Ideal for 1.2 mm mesh screens with 'lines' 2 mm apart and...