m3 hex nut standoff driver 3d models
218930 3d models found related to m3 hex nut standoff driver.thingiverse
Handy tool for screwing/unscrewing M3 Hex nuts and standoffs. Our FPV forum: http://www.IntoFPV.com FB Multirotor Group: https://www.facebook.com/groups/Copter.Fans/ I printed mine with Ultimaker 2+ with Polymaker Filament. To account for shrinkage...
thingiverse
Designed to be used as PCB standoff when building a quadrocopter, but obviously, it can be used in any PCB or other application. Should accept a M3 screws without any problem. NOTE: I tested a 8mm version printed with eSun ePA (nylon) filament and...
thingiverse
I have ordered some brass ones, but given the amount of fasteners and overall rugged design of this aircraft, I found that these standoffs, which I made just for the sake of testing the assembly until my brass spacers arrived, actually held the quad...
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
I didn't have a nut driver for an M3 nut..... so I made one. This fits into a 6-way screwdriver from Lowes. ...
thingiverse
This has a hex hole on the end that should be just about the right size for a single M3 nut. My machine calibration might be a bit off, so the hole might be too big, let me know! The hole should be snug enough that the nut stays in a little past...
thingiverse
It's a slighty modified version of M3 nut toll by fns720http://www.thingiverse.com/thing:57897 I've opened one side for better nut handling, and hollowed more the main one so even higer and auto lock nuts can be used. Instructions 0.2 need a bit...
thingiverse
Used to tighten m3 nuts into hard to reach spots. This one is also available in m5 size Print the part with wide flat part to the bottom. Print with slow speed, because the printer starts to oscillate if you print too fast. If the fit with the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: nut_thickness = 20 knurled_strong = 5 diameter_2 = 125 diameter_1 = 125 screw_hole_diameter = 55 nut_width = 5.42 cross_section = 0...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: nut_width = 5.42 bottom_thickness = 0 screw_hole_diameter = 55 knurled_strong = 5 cross_section = 0 knurled_height = 50 supportless_friendly = 1...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: nut_thickness = 30 knurled_strong = 5 screw_hole_diameter = 55 diameter_2 = 150 diameter_1 = 125 cross_section = 0 knurled_density = 50 nut_width...
thingiverse
A little driver for 4mm hex nut for RC quadcopter standoffs for FC, VTX and ESC
thingiverse
Knob for hand fastening M3 hex nut Notice: Put nut immediately in finished print. Please let me know in comments, how did you use it. ... Thanks
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026
thingiverse
Customized version of https://www.thingiverse.com/thing:2761026 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2761026