m3d filament
173657 3d models found related to m3d filament.thingiverse
This is M3D filament holder I downloaded from printm3d.com. ...I did not create this but I hope it helps.
thingiverse
Just a remixed filament guide. ... Print Settings Printer: M3D Micro Rafts: Doesn't Matter Supports: Yes
thingiverse
I made this for holding my varies filament spools. ...Print Settings Printer: M3D Rafts: No Supports: No Resolution: Low Infill: 10%
cults3d
I made this small thing that holds the filament of the M3D to prevent the friction caused by the filament touching the border of the filament hole at the top of the nozzle. ...Hope it works for you!
thingiverse
I made this small thing that holds the filament of the M3D to prevent the friction caused by the filament touching the border of the filament hole at the top of the nozzle. ...Hope it works for you!
thingiverse
A filament Guide for the M3d printer. For use when using an 3rd party standard or large spool. Clips onto the top of the M3d housing on either the left (My preference) or right side. Just added a new wider guide for a little more filament clearance...
thingiverse
This filament cleaner is designed to be used on an M3D, of course it could be used on any other printer, The top is made so that a small piece of a paper towel or anything else that could clean the filament can be put inside the cylinder and clean it...
pinshape
SummaryThis filament cleaner is designed to be used on an M3D, of course it could be used on any other printer, The top is made so that a small piece of a paper towel or anything else that could clean the filament can be put inside the cylinder and...
thingiverse
Lightweight and practical filament guide for the M3D micro printer! It snaps instantly to the side of the printer-frame. I decided to reduce the thickness and also remove as much materials as possible from the original version to make the...
thingiverse
As the cover for the extruder of M3D+ is not firmly cover that whenever the cover is loose, soft filament may bend at the insertion place and lead to the filament unable to feed into the extruder for printing. Thus this very primitive filament guide...
thingiverse
Designed to be used with the M3D Horizontal overhead filament holder and my M3D spool holder center with bearing for the holder and 608 bearings. I tried using this filament guide, but the filament kept getting stuck between bearing and the side. I...
thingiverse
Its a Filament Guide for the M3D Micro Printer that clips nicely above the extruder. I use this personally in conjunction with the External Filament Spool holder posted here: http://www.thingiverse.com/thing:761893 Your angle my vary slightly which...
thingiverse
Simple remix of http://www.thingiverse.com/thing:858100 to print 3 filament guides at once. --- Original description --- This is a remix of http://thingiverse.com/thing:746048. I made the clip twice as thick (total of 6mm) and I closed up the gap...
pinshape
I made the clip twice as thick (total of 6mm) and I closed up the gap a bit more so it holds onto the M3D cable better. I left the filament hole the same. The pictures above are 6mm thick, but I didn't tighten up the clamp part on those. ... It is...
thingiverse
I made the clip twice as thick (total of 6mm) and I closed up the gap a bit more so it holds onto the M3D cable better. I left the filament hole the same. The pictures above are 6mm thick, but I didn't tighten up the clamp part on those. ... It is...
thingiverse
A Spool made for The MIcro 3D printer/ Side mount Print Settings Printer: Micro 3D (M3D) Rafts: No Supports: No Resolution: Medium Quality Infill: Double Wall Hollow Notes: Only Made for Micro How I Designed This Designed in 123design
pinshape
SummaryI made this for holding my varies filament spools.Print SettingsPrinter: M3DRafts: NoSupports: NoResolution: LowInfill: 10%
thingiverse
I needed to stop my filament from larger spools from bunching up... ...
thingiverse
Version 2 of the M3D filament guide. I wanted to see if the purely vertical version or an angled version worked better. A simple side hook filament guide for the M3D micro printer. If you are using the M3D initial spool (from the M3D download...
thingiverse
Version 3 of the M3D filament guide. I wanted to see if the purely vertical version or an angled version worked better, but then had some minor issues with the filament not sliding smoothly through the opening. Not wanting to give up on the idea, I...
thingiverse
... Instructions The Sample is printed in Medium/Medium without raft. ... To use it first put the spacer into your filament spool, then push it on your holder tube. ...The tube will keep the spacer streched to fit perfectly.
thingiverse
Customized version of http://www.thingiverse.com/thing:990972 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=990972
grabcad
M3D filament guide feeds the filament off of large and small external filament rolls while providing a counter bore suitable for 5mm OD PTFE tubing to go between this guide and the print head. It is a snap fit over the plastic body of the printer. ... ...
thingiverse
M3D filament guide feeds the filament off of large and small external filament rolls while providing a counter bore suitable for 5mm OD PTFE tubing to go between this guide and the print head. It is a snap fit over the plastic body of the printer.
thingiverse
... 2.0 of the filament cleaner, fits a little looser and isn't as loud. ... With the old version the filament would snag the sides as it went through which made it noisy. ...Also the part that holds the paper towel is much more economical and practical.